Post on 18-May-2018
transcript
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
EASY FV WALL
IT
Telecontrollo GSM/GPRS conforme AEEG 421/2014 CEI 0-16 allegato M.Il dispositivo EASY soddisfa i requisiti della delibera dell’Autorità dell’energia elettrica, gas e sistema idrico, finalizzata a garantire la sicurezza del sistema elettrico nazionale.
La delibera prevede l’obbligatorietà di installazione del sistema di telecontrollo per distacco, gestito dal proprietario della rete per impianti di produzione (fotovoltaici/eolici/cogenerazione) di potenza uguale o maggiore 100 kW.EASY può essere collegato direttamente all’interfaccia SPI e attraverso i comandi remoti predisposti e conformi alla direttiva, può intervenire allo stacco e diagnosi remota.
Telecontrollo
• attivazione/disattivazione del DO tramite SMS con protocollo compliant AEEG 421/2014 CEI 0-16 allegato M• invio dello stato del DI tramite SMS con protocollo compliant AEEG 421/2014 CEI 0-16 allegato M• richiedere lo STATO dell’impianto da remoto con SMS• gestione lista dei CLI abilitati (fino a 50)• gestione backup dell’alimentazione con 3 batterie interne ricaricabili (3XAAA)• 1 seriale RS232 TTL disponibile per interfacciamento a SPI (opzionale convertitore da TTL a RS232 o RS485)• 1 seriale mini USB per programmazione- parametrizzazione comandi• invio allarme mancanza rete parametrizzabile (se batterie di backup inserite)• misurazione della temperatura su sonda interna interrogabile da remoto tramite SMS• misurazione della temperatura su sonda esterna (opzionale) interrogabile da remoto tramite SMS• completa parametrizzazione da remoto tramite SMS• aggiornamento completo dell’applicazione da remoto in caso di upgrade normative e/o aggiunta funzioni
EN
GSM/GPRS remote control compliant AEEG 421/2014 CEI 0-16 annex M.The device EASY fullfills the requirements of thedeliberation of Authority for electric power, gas andwater system, finalized to guarantee the national power system security.
The deliberation defines the mandatory rules ofinstalling the remote control system for shutting down power, managed by the owner of the productionplant network (photovoltaic/eolic/cogeneration) upto or exceeding 100 kW.
EASY can be directly connected to the SPI interface and can operate with the switching off and remote diagnosis through remote controls preset according to the deliberation.
Remote control
• activation/deactivation of DO by SMS with compliant protocol AEEG 421/2014 CEI 0-16 annex M• dispatch of DI state by SMS with compliant protocol AEEG 421/2014 CEI 0-16 annex M• STATUS remote request of the implant with SMS• management of enabled CLI (up to 50)• power backup management by 3 internal rechargeable batteries (3XAAA)• 1 serial RS232 TTL available for interfacing to SPI (optional adaptor from TTL to RS232 or RS485)• 1 mini serial USB for command programming/setup• alarm warning for missing power supply (in case of backup batteries inside)• measurement of temperature on an internal probe, by remote through SMS• measurement of temperature on an external probe (optional), by remote through SMS• full setup by SMS• upgrade of application by remote in case of normative upgrades and/or addition of new features
ST_
0000
22_r
cx_g
prs_
it_en
_06_
2014
ST_
0000
27_e
asy
fv w
all_
it_en
_04_
2015
_Rev
.04_
foto
volta
ico
Conforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
AlimentazionePower supply
12Vdc (min 9Vdc, max 14 Vdc) Assorbimento: 3.5W Max;tramite alimentatore 230Vac fornito in dotazione 12Vdc (min 9Vdc, max 14 Vdc) Absorption: 3.5W Max;power supply by 230Vac power adaptor included
Ingressi DIDI Inputs
n°2 da collegare su contatti puliti esterni (polarizzati da tensione del modem)n°2 to be connected on external free contacts (voltage polarized by the modem)
InterfacceInterfaces
n°1 seriale RS232 TTL • n°1 seriale mini USB per programmazionen°1 serial RS232 TTL • n°1 mini serial USB for programming
Modulo di comunicazioneCommunication Module
modem quad band 850-900-1800-1900 MHz con OS proprietario e set di comandi AT standardquad band modem 850-900-1800-1900 MHz with proprietary OS and AT standard commands
Uscite DODO outputs
2 con contatti liberi da tensione2 with voltage free contacts
Portata contattiContact rating 5A 30Vdc, 3A 400Vac (cosφ 1)
Protocollo di comunicazioneCommunication Protocol
comandi SMS con protocollo compliant AEEG 421/2014 CEI 0-16 allegato MSMS commands with compatible protocol AEEG 421/2014 CEI 0-16 annex M
Pulsanti per test uscitePush buttons
2 frontali per commutazione relè (test manuale delle uscite DO)2 front for manual testing of the DO outputs
Sensore di misuraMeasuring sensor
1 sonda temperatura integrata1 integrated temperature probe
Sensore di misura opzionaleMeasuring sensor optional
1 tipo sonda NTC 10Kohm 1% - Lunghezza massima cablaggio 5 metri - non in dotazione1 probe type NTC 10Kohm 1% - maximum length wiring 5 meters - not supplied
Batterie ricaricabiliRechargeable batteries
3 x AAA ministilo - minimo 800mAh - non in dotazione3 x AAA - minimum 800mAh - not supplied
MorsettieraTerminal block
morsetti a vitescrew terminals
Temperatura di funzionamentoOperating Temperature -20°C +55°C
Dimensioni (LxPxA)Dimensions (LxPxA) 75x25x75 mm
Protezione Protection IP30
Prestazioni antenna standardAntenna standard performance
Polarizzazione verticale Gain 3db Frequency range: A => 890-960MHz B=>1710-1990MH Bandwidth: A=>70MHz B =>170MHz Vertical polarization Gain 3db Frequency range: A => 890-960MHz B=>1710-1990MH Bandwidth: A=>70MHz B =>170MHz
INTERFACCIA SPISPI INTERFACE
USB INTERFACE
INTERFACCIAUSB PER PROGRAMMAZIONE 12 VDC 230 VAC
ALIMENTAZIONE IN DOTAZIONEPOWEREQUIPMENT
BATTERIE INTERNEBACKUP OPZIONALIINTERNAL BATTERYOPTIONAL BACKUP
UPS
STATO(CONFERMAAPERTURA)
STATUS(FEEDBACK
OF OPENING)
Q Y
TELEDISTACCO(COMANDO DIAPERTURA)
REMOTEDISCONNECTION
(OPENCOMMAND)
DI / DOINTEGRATI INTEGRATED
EASY
INTERFACCIASERIALE OPZIONALE
OPTIONALSERIAL INTERFACE
USCITAOUTPUT
INGRESSO TELESCATTOREMOTE TRIP INPUT
TTL 232
RS2
32 O
RS4
85
EASY FV WALL Conforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
PMVF 30 LOVATO
MC3V MICROELETTRICA SCIENTIFICA
I1
TA1
V2V1V4 V3 S1I3I2
MISURA CORRENTI
S2S2 S1 S1 S2
TA2GENERAZIONE
FEEDBACK A SPIFEEDBACK A GSM
11 12 14 21 22 24 + COM - IN1I N2 IN3I N4
INGRESSI DIGITALI
DDI
PMVF 30
11 12 14 21 22 24
V5
TV3T V4 TV5
DG
L1 L2 L3
RINCALZO
USCITE4 TUO3 TUO2 TUO1 TUO
USCITE
RICHIUSURAAUTOMATICA
ALLARMEPROGRAMMABILE
❸
(OPZIONALE EXP10 03)
A1 A2--- +
100...400VAC110...250VDC
12...48VDC❶
INGRESSO TENSIONI50 - 500V~ AC
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
DDI
USCITA TEMPORIZZATA
PER LA RICONNESSIONE
AUTOMATICA
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
EASY FV WALL Conforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPI
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
NV10P THYTRONIC
NV10P
Utenzeprivilegiate
Tr
ip - NV10P eteledistacco (K1)
+UAUX
-UAUX
A9
A10
A11
A12A13
A14
A3A4A5
A6A7A8K2
K3
K4
K5
K6
K1
RS
232
FRONT PANEL
CIR
CU
ITI D
’EN
TRAT
A V
OLT
ME
TRIC
I
RE
LE’ F
INA
LI
A19A20
A21A22
+UAUX
+UAUX
-UAUX
Comandoabilitazione richiusura
Comandochiusura
BF (K2)
BF (K2)UAUX
A1A2
ING
RE
SS
I DIG
ITA
LI
IN1
IN2
B5
B6
B3
B4
B1
B2 UL1
UL2
UL3
52b
DI
-UAU
X
Finecorsa interruttore aperto (52b)
~
L1L2L3
UE
da
dn
N
A
B7
B8
-UAUX
+UAUX
Comando remotoblocco della richiusura
D1
ETH
ER
NE
T
E1
THY
BU
S
+UAUX
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
EASY FV WALL Conforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPI
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
DIA3S SEB-BARLASSINA
-UAUX
+UAUX
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
EASY FV WALL Conforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPI
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
DIA4N SEB-BARLASSINA
-UAUX
+UAUX
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
EASY FV WALL Conforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPI
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
542 plus ABB
Comandochiusura
52bDI
APER
TURA
DA R
EMO
TOCO
NSEN
SOCH
IUSU
RACH
IUSU
RADA
REM
OTO
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
EASY FV WALL Conforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPI
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
IT
Telecontrollo GSM/GPRS conforme AEEG 421/2014 CEI 0-16 allegato M.Il dispositivo EASY soddisfa i requisiti della delibera dell’Autorità dell’energia elettrica, gas e sistema idrico, finalizzata a garantire la sicurezza del sistema elettrico nazionale.
La delibera prevede l’obbligatorietà di installazione del sistema di telecontrollo per distacco, gestito dal proprietario della rete per impianti di produzione (fotovoltaici/eolici/cogenerazione) di potenza uguale o maggiore 100 kW.EASY può essere collegato direttamente all’interfaccia SPI e attraverso i comandi remoti predisposti e conformi alla direttiva, può intervenire allo stacco e diagnosi remota.
Telecontrollo
• attivazione/disattivazione del DO tramite SMS con protocollo compliant AEEG 421/2014 CEI 0-16 allegato M• invio dello stato del DI tramite SMS con protocollo compliant AEEG 421/2014 CEI 0-16 allegato M• richiedere lo STATO dell’impianto da remoto con SMS• gestione lista dei CLI abilitati (fino a 50)• gestione backup dell’alimentazione con 3 batterie interne ricaricabili (3XAAA)• 1 seriale RS232 TTL disponibile per interfacciamento a SPI (opzionale convertitore da TTL a RS232 o RS485)• 1 seriale mini USB per programmazione- parametrizzazione comandi• invio allarme mancanza rete parametrizzabile (se batterie di backup inserite)• misurazione della temperatura su sonda interna interrogabile da remoto tramite SMS• misurazione della temperatura su sonda esterna (opzionale) interrogabile da remoto tramite SMS• completa parametrizzazione da remoto tramite SMS• aggiornamento completo dell’applicazione da remoto in caso di upgrade normative e/o aggiunta funzioni
EN
GSM/GPRS remote control compliant AEEG 421/2014 CEI 0-16 annex M.The device EASY fullfills the requirements of thedeliberation of Authority for electric power, gas andwater system, finalized to guarantee the national power system security.
The deliberation defines the mandatory rules ofinstalling the remote control system for shutting down power, managed by the owner of the productionplant network (photovoltaic/eolic/cogeneration) upto or exceeding 100 kW.
EASY can be directly connected to the SPI interface and can operate with the switching off and remote diagnosis through remote controls preset according to the deliberation.
Remote control
• activation/deactivation of DO by SMS with compliant protocol AEEG 421/2014 CEI 0-16 annex M• dispatch of DI state by SMS with compliant protocol AEEG 421/2014 CEI 0-16 annex M• STATUS remote request of the implant with SMS• management of enabled CLI (up to 50)• power backup management by 3 internal rechargeable batteries (3XAAA)• 1 serial RS232 TTL available for interfacing to SPI (optional adaptor from TTL to RS232 or RS485)• 1 mini serial USB for command programming/setup• alarm warning for missing power supply (in case of backup batteries inside)• measurement of temperature on an internal probe, by remote through SMS• measurement of temperature on an external probe (optional), by remote through SMS• full setup by SMS• upgrade of application by remote in case of normative upgrades and/or addition of new features
ST_
0000
22_r
cx_g
prs_
it_en
_06_
2014
EASY FV DINConforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
ST_
0000
32_e
asy
fv d
in_i
t_en
_04_
2015
_Rev
.04_
foto
volta
ico
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
AlimentazionePower supply
12Vdc (min 9Vdc, max 14 Vdc) Assorbimento: 3.5W Max;Alimentatore non fornito in dotazione 12Vdc (min 9Vdc, max 14 Vdc) Absopbtion: 3.5W Max;Power supply not included
Ingressi DIDI Inputs
n°2 da collegare su contatti puliti esterni (polarizzati da tensione del modem)n°2 to be connected on external free contacts (voltage polarized by the modem)
InterfacceInterfaces
n°1 seriale RS232 TTL • n°1 seriale mini USB per programmazionen°1 serial RS232 TTL • n°1 mini serial USB for programming
Modulo di comunicazioneCommunication Module
modem quad band 850-900-1800-1900 MHz con OS proprietario e set di comandi AT standardquad band modem 850-900-1800-1900 MHz with proprietary OS and AT standard commands
Uscite DODO outputs
2 con contatti liberi da tensione2 with voltage free contacts
Portata contattiContact rating 5A 30Vdc, 3A 400Vac (cosφ 1)
Protocollo di comunicazioneCommunication Protocol
comandi SMS con protocollo compliant AEEG 421/2014 CEI 0-16 allegato MSMS commands with compatible protocol AEEG 421/2014 CEI 0-16 annex M
Pulsanti per test uscitePush buttons
2 frontali per commutazione relè (test manuale delle uscite DO)2 front for manual testing of the DO outputs
Sensore di misuraMeasuring sensor
1 sonda temperatura integrata1 integrated temperature probe
Sensore di misura opzionaleMeasuring sensor optional
1 tipo sonda NTC 10Kohm 1% - Lunghezza massima cablaggio 5 metri - non in dotazione1 probe type NTC 10Kohm 1% - maximum length wiring 5 meters - not supplied
Batterie ricaricabiliRechargeable batteries
3 x AAA ministilo - minimo 800mAh - non in dotazione3 x AAA - minimum 800mAh - not supplied
MorsettieraTerminal block
morsetti a vitescrew terminals
Temperatura di funzionamentoOperating Temperature -20°C +55°C
Dimensioni (LxPxA)Dimensions (LxPxA) 4moduli DIN
Protezione Protection IP20
Prestazioni antenna standardAntenna standard performance
Polarizzazione verticale Gain 3db Frequency range: A => 890-960MHz B=>1710-1990MH Bandwidth: A=>70MHz B =>170MHz Vertical polarization Gain 3db Frequency range: A => 890-960MHz B=>1710-1990MH Bandwidth: A=>70MHz B =>170MHz
INTERFACCIA SPISPI INTERFACE
USB INTERFACE
INTERFACCIAUSB PER PROGRAMMAZIONE 12 VDC 230 VAC
ALIMENTAZIONE IN DOTAZIONEPOWEREQUIPMENT
UPS
STATO(CONFERMAAPERTURA)
STATUS(FEEDBACK
OF OPENING)
Q Y
TELEDISTACCO(COMANDO DIAPERTURA)
REMOTEDISCONNECTION
(OPENCOMMAND)
DI / DOINTEGRATI INTEGRATED
INTERFACCIASERIALE OPZIONALE
OPTIONALSERIAL INTERFACE
USCITAOUTPUT
INGRESSO TELESCATTOREMOTE TRIP INPUT
TTL 232
RS2
32 O
RS4
85
BATTERIE INTERNEBACKUP OPZIONALIINTERNAL BATTERYOPTIONAL BACKUP
EASY
EASY FV DINConforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPIPMVF 30 LOVATO
MC3V MICROELETTRICA SCIENTIFICA
DDI
I1
TA1
V2V1V4 V3 S1I3I2
MISURA CORRENTI
S2S2 S1 S1 S2
TA2GENERAZIONE
FEEDBACK A SPIFEEDBACK A GSM
11 12 14 21 22 24 + COM - IN1I N2 IN3I N4
INGRESSI DIGITALI
DDI
PMVF 30
11 12 14 21 22 24
V5
TV3T V4 TV5
DG
L1 L2 L3
RINCALZO
USCITE4 TUO3 TUO2 TUO1 TUO
USCITE
RICHIUSURAAUTOMATICA
ALLARMEPROGRAMMABILE
❸
(OPZIONALE EXP10 03)
A1 A2--- +
100...400VAC110...250VDC
12...48VDC❶
INGRESSO TENSIONI50 - 500V~ AC
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
EASY FV DINConforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
3XAAARECHARGE
INSIDE
3XAAARECHARGE
INSIDE
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
NV10P THYTRONIC
NV10P
Utenzeprivilegiate
Trip - NV10P eteledistacco (K1)
+UAUX
-UAUX
A9
A10
A11
A12A13
A14
A3A4A5
A6A7A8K2
K3
K4
K5
K6
K1
RS
232
FRONT PANEL
CIR
CU
ITI D
’EN
TRAT
A V
OLT
ME
TRIC
I
RE
LE’ F
INA
LI
A19A20
A21A22
+UAUX
+UAUX
-UAUX
Comandoabilitazione richiusura
Comandochiusura
BF (K2)
BF (K2)
UAUX
A1A2
ING
RE
SS
I DIG
ITA
LI
IN1
IN2
B5
B6
B3
B4
B1
B2 UL1
UL2
UL3
52bDI
-UAUX
Finecorsa interruttore aperto (52b)
~
L1L2L3
UE
da
dn
N
A
B7
B8
-UAUX
+UAUX
Comando remotoblocco della richiusura
D1
ETH
ER
NE
T
E1
THY
BU
S
+UAUX
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
EASY FV DINConforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPI
3XAAARECHARGE
INSIDE
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
DIA3S SEB-BARLASSINA
EASY FV DINConforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPI
-UAUX
+UAUX
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
3XAAARECHARGE
INSIDE
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
DIA4N SEB-BARLASSINA
EASY FV DINConforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
Connessione con SPIConnection with SPI
-UAUX
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
3XAAARECHARGE
INSIDE
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
+UAUX
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces
Shitek Technology S.r.l. - Via Malerbe,3 - 36040 - Grumolo delle Abbadesse (VI) - ItaliaT. +39 0444 1800191 - F. +39 049 7960910 - www.shitek.it - info@shitek.it
542 plus ABB
Comandochiusur
a52bDI
APER
TURA
DA R
EMO
TOCO
NSEN
SOCH
IUSU
RACH
IUSU
RADA
REM
OTO
Conferma apertura (IN1-GND):ingresso aperto = impianto connessoingresso chiuso = impianto disconnesso
Comando apertura(OUT1 - COM1):uscita aperta = ripristinouscita chiusa = distacco
EASY FV DIN Conforme alla Delibera AAEG 421/2014/R/eel,Norma CEI 0-16 ed.III:2012-12 Allegato M
3XAAARECHARGE
INSIDE
USCITA TEMPORIZZATAPER LA RICONNESSIONE
AUTOMATICA
Connessione con SPIConnection with SPI
Schemi di esempio, verificare l’esatta configurazione con il produttore dello strumento.L’Azienda declina ogni responsabilità per la non correttezza di eventuali errate e/o mancate connessioni/configurazioni.Example scheme, check the exact configuration with the manufacturer of the instrument.The Company accepts no responsibility for the inaccuracy of any wrong and/or missed connections/configurations. S
chem
i ele
ttric
i lib
eram
ente
trat
ti da
font
i pub
blic
he -
Wiri
ng d
iagr
ams
freel
y tra
its p
ublic
sou
rces