Date post: | 22-Jul-2016 |
Category: |
Documents |
Upload: | seitron-spa |
View: | 218 times |
Download: | 2 times |
www.seitron.it
Sicurezza gas residenziale - Residential gas detectors
MADE IN ITALY
www.seitron.it
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
I RILEVATORI DI FUGHE DI GAS PER USO RESIDENZIALE DI SEITRONSeitron progetta e produce rilevatori di gas per uso residenziale o civile da più di vent’anni. Fin dall’inizio la scelta è stata di limitarsi a 3 gas (2 gas esplosivi, metano e GPL, ed 1 gas tossico, monossido di carbonio - CO) e di produrre rilevatori di fughe di gas che diano il massimo delle garanzie a chi li utilizza per la propria sicurezza: -Allarme acustico ed uscita a relè per elettrovalvola di intercettazione normalmente chiusa (N.C.) e normalmente aperta (N.A.). -Alimentazione a 230V. LA DIFESA CONTRO L’AVVELENAMENTO DA MONOSSIDO DI CARBONIO (CO). Il monossido di carbonio (CO) è stato anche definito il killer silenzioso: infatti è inodore, incolore ed insapore. Inoltre è leggermente meno denso dell’aria per cui tende ad accumularsi lentamente nella parte alta degli ambienti chiusi.La sua caratteristica più pericolosa è che l’essere umano non può accorgersi della sua presenza. I casi mortali più insidiosi riguardano persone che si addormentano con un lieve mal di testa e non si svegliano mai più. Ciò dovrebbe rendere evidente a tutti l’utilità dei rilevatori di CO.
GAS LEAK DETECTORS FOR RESIDENTIAL USE BY SEITRON Seitron designs and manufactures gas detectors for civil or domestic use since more than twenty years. From the beginning the choice was limited to 3 gases (2 explosive gases, methane and LPG, and 1 toxic gas, carbon monoxide - CO) and to produce gas leak detectors that deliver the maximum guarantees to those who use them for their own safety: -Only detectors with acoustic alarm and relay output to activate normally closed (N.C.) and normally open (N.O.) electrovalve. -Only detectors powered with 230V mains voltage. DEFENSE AGAINST POISONING BY CARBON MONOXIDE (CO). Carbon monoxide (CO) has been named the silent killer: it is odorless, colorless and tasteless. It is also slightly less dense than air, so it tends to accumulate slowly in the upper part of the rooms. Its most dangerous characteristic is that humans cannot notice his presence. The most insidious fatal cases concern people who fall asleep with a slight headache and never wake up again. This should make clear to all the usefulness of CO alarms.
CARATTERISTICA / FEATURE BEAGLE SEGUGIO
Numero Zone / Zone Number 1 2
Metano / Natural Gas Si / Yes Si / Yes
GPL / LPG Si / Yes Si / Yes
CO / CO Si / Yes Si / Yes
Kit Con Ev Gas 3 / 4 “ (NA/NC) / Kit With 3/4” Gas Electrovalve (NO/NC) Si / Yes Si / Yes
Alimentazione / Power Supply 230 V~ 230 V~
Allarme Acustico / Acoustic Alarm Si / Yes Si / Yes
Uscita per Ev Gas 230 V~ / Output for 230V~ Gas Ev Si / Yes Si / Yes
Uscita per Ev Gas 12 V / Output for 12V= Gas Ev No Si / Yes
Vita Utile Sensore / Sensor Life 5 Anni / 5 Years 5 Anni / 5 Years
Sensore sostituibile precalibrato / Precalibrated replaceable sensor Si / Yes Si / Yes
Garanzia Strumento / Instrument Warranty 3 Anni / 3 Years 3 Anni / 3 Years
Pulsante Test Allarme / Alarm Test Button Si / Yes Si / Yes
Led Giallo Segnalazione Guasti / Yellow LED for Fault Alarm Si / Yes Si / Yes
Led Rosso Allarme Gas / Red LED for Gas Alarm Si / Yes Si / Yes
Led Verde Unità in Servizio / Green LED for Working Unit Si / Yes Si / Yes
Dimensioni / Dimensions L85 x A107 x P38 mm W85 x H107 x D38 mm
L148 x A84 x P40 mm W148 x H84 x D40 mm
TABELLA COMPARATIVA BEAGLE & SEGUGIO / BEAGLE & SEGUGIO COMPARISON CHART
www.seitron.it
RGD ME5 MP1R: Esempi di collegamento / Typical wiring
COD. RGD ME5 MP1R € 90
COD. RDM BA1 Con cavo spina, 2 m / With 2 m cable and plug € 99
BEAGLE plus METANO
RILEVATORE FUGHE GAS - METANO -Rilevatore di fughe di gas metano per uso domestico con possibilità di comandare direttamente un’elettrovalvola a 230V~. Pulsante di test. Conforme alla norma CEI-EN 50194-1. Il marchio di qualità IMQ e la conformità alla norma CEI-EN 50194-1 attestano l’assoluta affidabilità e l’efficienza dell’apparecchio. Sensore precalibrato, sostituibile direttamente dall’utente.
GAS LEAKAGE DETECTOR - METHANE -Domestic methane gas detector with output for driving 230V~ cut-off valves. Test button. In compliance with CEI-EN 50194-1 standard. IMQ quality mark and compliance with CEI-EN 50194-1certify the absolute reliability and efficiency of the device. Precalibrated sensor, directly replaceable by user.
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
Alimentazione 230V~ -15/+10% 50HzTipo di sensore SnO2 A semiconduttore Sensore precalibrato, sostituibile direttamente dall’utente Soglia di intervento 10% L.I.E.Uscita(relè) 5(2)A @ 250V~ SPDTVita utile sensore 5 anniSegnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guastoSegnalazione LED rosso AllarmeGrado di protezione IP42Dimensioni A107 L85 P38mm
Power supply 230V~ -15/+10% 50HzSensor type SnO2 Semiconductor Precalibrated sensor, directly replaceable by userAlarm threshold 10% L.E.L.Output (relay) 5(2)A @ 250V~ SPDTSensor life 5 yearsGreen LED indicator Detector activeYellow LED indicator Detector failureRed LED indicator Alarm IP rating IP42 Dimensions H107 W85 D38mm
www.seitron.it
RGD GP5 MP1R: Esempi di collegamento / Typical wiring
BEAGLE plus GPL
RILEVATORE FUGHE GAS - GPL -Rilevatore di fughe di gas GPL per uso domestico con possibilità di comandare direttamente un’elettrovalvola a 230V~. Pulsante di test. Conforme alla norma CEI-EN 50194-1. Il marchio di qualità IMQ e la conformità alla norma CEI-EN 50194-1 attestano l’assoluta affidabilità e l’efficienza dell’apparecchio. Sensore precalibrato, sostituibile direttamente dall’utente.
GAS LEAKAGE DETECTOR - LPG -Domestic LPG gas detector with output for driving 230V~ cut-off valves. Test button. In compliance with CEI-EN 50194-1 standard. IMQ quality mark and compliance with CEI-EN 50194-1 certify the absolute reliability and efficiency of the device. Precalibrated sensor, directly replaceable by user.
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
Alimentazione 230V~ -15/+10% 50HzTipo di sensore SnO2 A semiconduttore Sensore precalibrato, sostituibile direttamente dall’utente Soglia di intervento 10% L.I.E.Uscita(relè) 5(2)A @ 250V~ SPDTVita utile sensore 5 anniSegnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guastoSegnalazione LED rosso AllarmeGrado di protezione IP42Dimensioni A107 L85 P38mm
Power supply 230V~ -15/+10% 50HzSensor type SnO2 Semiconductor Precalibrated sensor, directly replaceable by userAlarm threshold 10% L.E.L.Output (relay) 5(2)A @ 250V~ SPDTSensor life 5 yearsGreen LED indicator Detector activeYellow LED indicator Detector failureRed LED indicator Alarm IP rating IP42 Dimensions H107 W85 D38mm
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
COD. RGD GP5 MP1R € 90
COD. RDG BA1 Con cavo spina, 2 m / With 2 m cable and plug € 99
www.seitron.it
RGD CK5 MP1S: Esempi di collegamento / Typical wiring
BEAGLE CO AD ACCUMULOBEAGLE CO ACCUMULATION MODE
RILEVATORE FUGHE GAS - CO -Rilevatore di monossido di carbonio per uso civile a microprocessore con possibilità di comandare direttamente elettrovalvole, ventole o altri attuatori a 230V. Rivelazione del monossido di carbonio ad accumulo: simula il comportamento di accumulo del gas nel corpo umano secondo norma EN 50291-1.
GAS LEAKAGE DETECTOR - CO -Microprocessor based domestic carbon monoxide detector with output for cut-off valves, fans or any other electrical actuators with 230V power supply. Carbon monoxide detection with accumulation mode: it simulates the gas accumulation in the human body according to standard EN 50291-1.
Alimentazione 230V~ -±10% 50HzSensore interno Cella chimica precalibrata, sostituibile direttamente dall’utentePrima soglia di intervento ~30ppm CO per più di 120 minuti Uscita (relè) 5(2)A @ 250V~ SPDTPulsante Test/Reset allarmeAllarme acustico Acustico 85dB(A)@ 1mSegnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guastoSegnalazione LED rosso AllarmeGrado di protezione IP42Dimensioni A107 L85 P38mm
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
Power supply 230V~ -±10% 50HzInternal sensor Precalibrated chemical cell on module, directly replaceable by userFirst alarm threshold ~30ppm CO lasting for >120 minutesOutput (relay) 5(2)A @ 250V~ SPDTButton Test/Alarm reset Alarm Buzzer Buzzer 85dB(A)@ 1mGreen LED indicator Detector activeYellow LED indicator Detector failureRed LED indicator Alarm IP rating IP42 Dimensions H107 W85 D38mm
COD. RGD CK5 MP1S € 134
COD. RDC BA1 Con cavo spina, 2 m / With 2 m cable and plug € 144
www.seitron.it
RGD CM0 MP1: Typical wiring
BEAGLE DOUBLE
GAS LEAKAGE DETECTOR - METHANE AND CO -Domestic methane (CH4) gas and carbon monoxide (CO) detector with facility for driving 230V~ cut-off valves or fans. Test button.
Not compliant with EN 50291.
RESIDENTIAL GAS LEAKAGE DETECTORSTechnical features
Power supply 230V~ -15/+10% 50HzSensor type SnO2 SemiconductorAlarm threshold 10% L.E.L. CH4 80ppm COOutput (relay) 5A @ 250V~ SPDTSensor life 5 yearsGreen LED indicator Detector active
Yellow LED indicator Detector failure Multicolor LED indicator red: CH4 alarm blue: CO alarm red-blue: bothIP rating IP42Dimensions H107 W85 D38mm
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
COD. RGD CM0 MP1 € 150
www.seitron.it
KIT BEAGLE METANO
Kit comprendente un Rilevatore BEAGLE METANO (RGDME5MP1R) alimentato a 230V~, una elettrovalvola a riarmo manuale da 3/4” 230V~ e due riduzioni da 3/4” a 1/2”. Sensore precalibrato, sostituibile direttamente dall’utente.
KIT BEAGLE METHANE
Kit including 1 BEAGLE METHANE (RGDME5MP1R) gas detector with 230V~ power supply, 1 230V~ cut-off valve with manual reset, 2 x 3/4” to 1/2” nipples. Precalibrated sensor, directly replaceable by user.
KIT BEAGLE GPL
Kit comprendente un Rilevatore BEAGLE GPL (RGDGP5MP1R) alimentato a 230V~, una elettrovalvola a riarmo manuale da 3/4”. 230V~ e due riduzioni da 3/4” a 1/2”. Sensore precalibrato, sostituibile direttamente dall’utente.
KIT BEAGLE LPG
Kit including 1 BEAGLE LPG (RGDGP5MP1R) gas detector with 230V~ power supply, 1 230V~ cut-off valve with manual reset, 2 x 3/4” to 1/2” nipples. Precalibrated sensor, directly replaceable by user.
COD. KD M5R 00021 Kit con elettrovalvola N.A. / Kit with N.O. electrovalve € 152
COD. KD M5R 00022 Kit con elettrovalvola N.C. / Kit with N.C. electrovalve € 218
COD. KD G5R 00019 Kit con elettrovalvola N.A. / Kit with N.O. electrovalve € 152
COD. KD G5R 00020 Kit con elettrovalvola N.C. / Kit with N.C. electrovalve € 218
www.seitron.it
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
COD. DDM SM1 (metano-methane) € 150 COD. DDG SM1 (GPL-LPG) € 150
SEGUGIO WIRELESS: Esempi di collegamento / Typical wiring
SEGUGIO WIRELESS
RILEVATORE FUGHE GAS RADIO - METANO o GPL Versione del SEGUGIO plus METANO/GPL con modulo trasmettitore radio. Rilevatore di fughe di gas per uso domestico a microprocessore in grado di comandare direttamente elettrovalvole a 230V~ e a 12V~/=. Funzioni di tacitazione e test. Sensore precalibrato, sostituibile direttamente dall’utente. Il marchio di qualità IMQ (1) e la conformità alla norma CEI-EN 50194-1 attestano l’assoluta affidabilità ed efficienza dell’apparecchio. Il modulo trasmettitore radio invia gli stati di “guasto” e “allarme” ad un ricevitore per allarme gas DRG01M.
WIRELESS ENABLED GAS LEAKAGE DETECTOR METHANE or LPGVersion of SEGUGIO plus METANO/GPL equipped with a wireless radio transmitter. Microprocessor based domestic methane gas detector with output for both 230V~ and 12V~/= cut-off valves. Mute and test functions. Precalibrated sensor, directly replaceable by user. IMQ quality mark (1) and compliance with CEI-EN 50194-1 certify the absolute reliability and efficiency of the device. The wireless transmitter module allows to transmit “failure” and “alarm” states to the receiver for gas alarm DRG01M.
CON ELETTROVALVOLA NORMALMENTE APERTA A 230V~ E SENSORE REMOTO230V~ NORMALLY OPEN ELECTROVALVE AND REMOTE SENSOR
Alimentazione 230V~ 50HzUscita(relè) 6(2)A @ 250V~ SPDTTipo di sensore A semiconduttore SnO2
Sensore precalibrato, sostituibile direttamente dall’utenteVita utile sensore 5 anniSoglia di allarme 10% L.I.E.Segnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guastoSegnalazione LED rosso AllarmeSuoneria di allarme 85dB (A) @ 1mGrado di protezione IP42Dimensioni A84 L148 P40mmMarcatura del prodotto IMQFrequenza trasmissione 868,150 MHzMax distanza ricevitore 50 m
Power supply 230V~ 50HzOutput (relay) 6(2)A @ 250V~ SPDTSensor type SnO2 Semiconductor Precalibrated sensor, directly replaceable by userSensor life 5 yearsAlarm threshold 10% L.E.L.Green LED indicator Detector activeYellow LED indicator Detector failure Red LED indicator Alarm Alarm buzzer 85dB (A) @ 1m IP rating IP42 Dimensions H84 W148 D40mmProduct mark IMQTransmission frequency 868,150 MHzMax distance receiver 50 m
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
(1) Valido solamente nel caso di collegamento a filo dell’elettrovalvola - Only valid when the electrovalve is hard-wired
www.seitron.it
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
COD. DRG 01M € 150
RICEVITORE ALLARME GASRicevitore radio per SEGUGIO WIRELESS dotato di due relè di uscita SPDT per attivare un carico in caso di allarme gas e in caso di guasto del sensore o altro guasto. Due LED multicolore permettono la visualizzazione dello stato di “allarme” e di “guasto” oltre che la visualizzazione della qualità della comunicazione radio. Il DRG01M può essere associato tramite autoapprendimento a più di un SEGUGIO WIRELESS, fino ad un massimo di 12.
GAS ALARM RECEIVERWireless receiver for SEGUGIO WIRELESS, it features two SPDT relay outputs to activate a load in the event of a gas alarm and in the event of a sensor failure or other failure. Two multicolor LEDs provide “alarm” and “fault” status display as well as quality of radio communication display. The DRG01M can be associated by means of the self-learning procedure to more than one SEGUGIO WIRELESS, up to a maximum of 12.
DRG 01M: Esempi di collegamento / Typical wiring
Alimentazione 230V~ 50HzPotenza assorbita 11VAUscita (relè) 2x6A 250V~ Frequenza di trasmissione 868,150 MHzTipo di antenna Stilo internoIndicatori LED bicolore Stato gas/qualità trasmissioneGrado di protezione IP4XDimensioni A125 L78 P30,5mm
Power supply 230V~ 50HzPower absorption 11VAOutput (relay) 2x6A 250V~Transmission frequency 868,150 MHzAntenna type Internal stylusBicolour LED indicators Gas status/ transmission quality IP rating IP4X Dimensions H125 W78 D30,5mm
www.seitron.it
SEGUGIO plus METANO
RILEVATORE FUGHE GAS - METANO -Rilevatore di fughe di gas metano per uso domestico a microprocessore con possibilità di comandare direttamente elettrovalvole a 230V~ e a 12V~/=. Funzioni di tacitazione e test. Sensore precalibrato, sostituibile direttamente dall’utente. Il marchio di qualità IMQ e la conformità alla norma CEI-EN 50194-1 attestano l’assoluta affidabilità e l’efficienza dell’apparecchio.
GAS LEAKAGE DETECTOR - METHANE -Microprocessor based domestic methane gas detector with output for both 230V~ and 12V~/= cut-off valves. Mute and test functions. Precalibrated sensor, directly replaceable by user. IMQ quality mark and compliance with CEI-EN 50194-1 certify the absolute reliability and efficiency of the device.
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
Alimentazione 230V~ ±10% 50HzUscita(relè) 6(2)A @ 250V~ SPDTTipo di sensore A semiconduttore SnO2
Sensore precalibrato, sostituibile direttamente dall’utenteVita utile sensore 5 anniSoglia di allarme 10% L.I.E.Segnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guastoSegnalazione LED rosso AllarmeSuoneria di allarme 85dB (A) @ 1mGrado di protezione IP42Dimensioni A84 L148 P40mmMarcatura del prodotto IMQ
Power supply 230V~ ±10% 50HzOutput (relay) 6(2)A @ 250V~ SPDTSensor type SnO2 Semiconductor Precalibrated sensor, directly replaceable by userSensor life 5 yearsAlarm threshold 10% L.E.L.Green LED indicator Detector activeYellow LED indicator Detector failure Red LED indicator Alarm Alarm buzzer 85dB (A) @ 1m IP rating IP42 Dimensions H84 W148 D40mmProduct mark IMQ
Note: (1) Predisposizione per un sensore remoto (SGA ***) per il controllo di un secondo locale. (2) Tasto di verifica premuto per 1 sec.: tacitazione allarme per 10 minuti; premuto per 5 sec.: test per verifica funzionale e attivazione valvola (3) Batteria tampone: ACC SGB 6A. (4) Sensori remoti da utilizzare: SGA MET, SGA GPL.
Notes: (1) Facility for a remote sensor (SGA ***), for the control of a further zone. (2) Depressed button test for one sec.: it silences the buzzer for 10 minutes; depressed for at least 5 sec.: checks all internal functions and electrovalve activation. (3) Back-up battery: ACC SGB 6A. (4) The remote sensor to be used are: SGA MET, SGA GPL.
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
COD. RGD MET MP1R € 130
www.seitron.it
CON ELETTROVALVOLA NORM. CHIUSA A 12V~/= A BASSO ASSORBIMENTO12V~/= NORMALLY CLOSED LOW CONSUMPTION ELECTROVALVE
CON ELETTROVALVOLA NORM. APERTA A 12V~/= A BASSO ASSORBIMENTO12V~/= NORMALLY OPEN LOW CONSUMPTION ELECTROVALVE
CON ELETTROVALVOLA NORMALMENTE CHIUSA A 230V~ E SENSORE REMOTO230V~ NORMALLY CLOSED ELECTROVALVE AND REMOTE SENSOR
CON ELETTROVALVOLA NORMALMENTE APERTA A 230V~ E SENSORE REMOTO230V~ NORMALLY OPEN ELECTROVALVE AND REMOTE SENSOR
Esempi di collegamento di più rilevatori Segugio con comando di
un’unica elettrovalvola 12V.
Examples of wiring diagram with several Segugio detectors and one
single 12 V electrovalve.
Esempi di collegamento di più rilevatori Segugio con comando di
un’unica elettrovalvola 230V~.
Examples of wiring diagram with several Segugio detectors and one
single 230V~ electrovalve.
Note: (1) I sensori remoti da utilizzare sono: SGA MET, SGA GPL.Notes: (1) The remote sensors to be used are: SGA MET, SGA GPL.
RGD MET MP1R: Esempi di collegamento / Typical wiring
RGD --- MP1R: Esempi di collegamento / Typical wiring
RGD --- MP1R: Esempi di collegamento / Typical wiring
www.seitron.it
SEGUGIO plus GPL
RILEVATORE FUGHE GAS - GPL -Rilevatore di fughe di gas GPL per uso domestico a microprocessore con possibilità di comandare direttamente elettrovalvole a 230V~ e a 12V~/=. Funzioni di tacitazione e test. Sensore precalibrato, sostituibile direttamente dall’utente. Il marchio di qualità IMQ e la conformità alla norma CEI-EN 50194-1 attestano l’assoluta affidabilità e l’efficienza dell’apparecchio.
GAS LEAKAGE DETECTOR - LPG -Microprocessor based domestic LPG gas detector with output for both 230V~ and 12V~/= cut-off valves. Mute and test functions. Precalibrated sensor, directly replaceable by user. IMQ quality mark and compliance with CEI-EN 50194-1 certify the absolute reliability and efficiency of the device.
Alimentazione 230V~ ±10% 50HzUscita (relè) 6(2)A @ 250V~ SPDTTipo di sensore A semiconduttore SnO2
Sensore precalibrato, sostituibile direttamente dall’utenteVita utile sensore 5 anniSoglia di allarme 10% L.I.E.Segnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guastoSegnalazione LED rosso AllarmeSuoneria di allarme 85dB (A) @ 1mGradi di protezione IP42Dimensioni A84 L148 P40mmMarcatura del prodotto IMQ
Power supply 230V~ ±10% 50HzOutput (relay) 6(2)A @ 250V~ SPDTSensor type SnO2 semiconductor Precalibrated sensor, directly replaceable by userSensor life 5 yearsAlarm threshold 10% L.E.L.Green LED indicator Detector activeYellow LED indicator Detector failure Red LED indicator Alarm Alarm buzzer 85dB (A) @ 1m IP rating IP42 Dimensions H84 W148 D40mmProduct mark IMQ
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
Note: (1) Predisposizione per un sensore remoto (SGA ***) per il controllo di un secondo locale. (2) Tasto di verifica premuto per 1 sec.: tacitazione allarme per 10 minuti; premuto per 5 sec.: test per verifica funzionale e attivazione valvola (3) Batteria tampone: ACC SGB 6A. (4) Sensori remoti da utilizzare: SGA MET, SGA GPL.
Notes: (1) Facility for a remote sensor (SGA ***), for the control of a further zone. (2) Depressed button test for one sec.: it silences the buzzer for 10 minutes; depressed for at least 5 sec.: checks all internal functions and electrovalve activation. (3) Back-up battery: ACC SGB 6A. (4) The remote sensor to be used are: SGA MET, SGA GPL.
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
COD. RGD GPL MP1R € 130
www.seitron.it
RGD COK MP1: Esempi di collegamento / Typical wiring
Alimentazione 230V~ -15/+10% 50HzUscita (relè stagno) 6(2)A @ 250V~ SPDTSensore interno(1) Cella elettrochimicaPulsante Test-Reset allarmeAllarme Acustico 85dB(A) @ 1mSegnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guasto Segnalazione LED rosso AllarmeDimensioni A84 L148 P40mmGrado di protezione IP42
Power supply 230V~ -15/+10% 50HzOutput (tight relay) 6(2)A @ 250V~ SPDTInternal sensor(1) Electrochemical cellButton Alarm Test-ResetAlarm Buzzer 85dB(A) @ 1mGreen LED indicator Detector activeYellow LED indicator Detector failureRed LED indicator Alarm Dimensions H84 W148 D40mmIP rating IP42
Note: (1) Predisposizione per un sensore remoto (SGA ***) per il controllo di un secondo locale. (2) Tasto di verifica premuto per 1 sec.: tacitazione allarme per 10 minuti; premuto per 5 sec.: test per verifica funzionale e attivazione valvola. (3) Sensori remoti da utilizzare: SGA MET, SGA GPL.
Notes: (1) Facility for a remote sensor (SGA ***), for the control of a further zone. (2) Depressed button test for one sec.: it silences the buzzer for 10 minutes;depressed for at least 5 sec.: checks all internal functions and electrovalve activation. (3) The remote sensor to be used are: SGA MET, SGA GPL.
SEGUGIO CO ACCUMULO
RILEVATORE FUGHE GAS - CO -Rilevatore di monossido di carbonio per uso civile a microprocessore con possibilità di comandare direttamente elettrovalvole, ventole o altri attuatori a 230V~. Rivelazione del monossido di carbonio ad accumulo: simula il comportamento di accumulo del gas nel corpo umano secondo norma EN50291.
SEGUGIO CO ACCUMULATION MODE
GAS LEAKAGE DETECTOR - CO -Microprocessor based domestic carbon monoxide detector with output for cut-off valves, fans or any other electrical actuators with 230V~ power supply. Carbon monoxide detection with accumulation mode: it simulates the gas accumulation in the human body according to standard EN50291.
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
N.O.
COD. RGD COK MP1 € 155
www.seitron.it
SEGUGIO plus GPL
RILEVATORE FUGHE GAS - GPL -Rilevatore di fughe di gas GPL per uso domestico a microprocessore con possibilità di comandare direttamente elettrovalvole a 230V~ e a 12V~/=. Funzioni di tacitazione e test. Sensore precalibrato, sostituibile direttamente dall’utente. Il marchio di qualità IMQ e la conformità alla norma CEI-EN 50194-1 attestano l’assoluta affidabilità e l’efficienza dell’apparecchio.
GAS LEAKAGE DETECTOR - LPG -Microprocessor based domestic LPG gas detector with output for both 230V~ and 12V~/= cut-off valves. Mute and test functions. Precalibrated sensor, directly replaceable by user. IMQ quality mark and compliance with CEI-EN 50194-1 certify the absolute reliability and efficiency of the device.
Alimentazione 230V~ ±10% 50HzUscita (relè) 6(2)A @ 250V~ SPDTTipo di sensore A semiconduttore SnO2
Sensore precalibrato, sostituibile direttamente dall’utenteVita utile sensore 5 anniSoglia di allarme 10% L.I.E.Segnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guastoSegnalazione LED rosso AllarmeSuoneria di allarme 85dB (A) @ 1mGradi di protezione IP42Dimensioni A84 L148 P40mmMarcatura del prodotto IMQ
Power supply 230V~ ±10% 50HzOutput (relay) 6(2)A @ 250V~ SPDTSensor type SnO2 semiconductor Precalibrated sensor, directly replaceable by userSensor life 5 yearsAlarm threshold 10% L.E.L.Green LED indicator Detector activeYellow LED indicator Detector failure Red LED indicator Alarm Alarm buzzer 85dB (A) @ 1m IP rating IP42 Dimensions H84 W148 D40mmProduct mark IMQ
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
Note: (1) Predisposizione per un sensore remoto (SGA ***) per il controllo di un secondo locale. (2) Tasto di verifica premuto per 1 sec.: tacitazione allarme per 10 minuti; premuto per 5 sec.: test per verifica funzionale e attivazione valvola (3) Batteria tampone: ACC SGB 6A. (4) Sensori remoti da utilizzare: SGA MET, SGA GPL.
Notes: (1) Facility for a remote sensor (SGA ***), for the control of a further zone. (2) Depressed button test for one sec.: it silences the buzzer for 10 minutes; depressed for at least 5 sec.: checks all internal functions and electrovalve activation. (3) Back-up battery: ACC SGB 6A. (4) The remote sensor to be used are: SGA MET, SGA GPL.
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
COD. RGD GPL MP1R € 130
www.seitron.it
RGD COK MP1: Esempi di collegamento / Typical wiring
Alimentazione 230V~ -15/+10% 50HzUscita (relè stagno) 6(2)A @ 250V~ SPDTSensore interno(1) Cella elettrochimicaPulsante Test-Reset allarmeAllarme Acustico 85dB(A) @ 1mSegnalazione LED verde Rilevatore attivoSegnalazione LED giallo Rilevatore guasto Segnalazione LED rosso AllarmeDimensioni A84 L148 P40mmGrado di protezione IP42
Power supply 230V~ -15/+10% 50HzOutput (tight relay) 6(2)A @ 250V~ SPDTInternal sensor(1) Electrochemical cellButton Alarm Test-ResetAlarm Buzzer 85dB(A) @ 1mGreen LED indicator Detector activeYellow LED indicator Detector failureRed LED indicator Alarm Dimensions H84 W148 D40mmIP rating IP42
Note: (1) Predisposizione per un sensore remoto (SGA ***) per il controllo di un secondo locale. (2) Tasto di verifica premuto per 1 sec.: tacitazione allarme per 10 minuti; premuto per 5 sec.: test per verifica funzionale e attivazione valvola. (3) Sensori remoti da utilizzare: SGA MET, SGA GPL.
Notes: (1) Facility for a remote sensor (SGA ***), for the control of a further zone. (2) Depressed button test for one sec.: it silences the buzzer for 10 minutes;depressed for at least 5 sec.: checks all internal functions and electrovalve activation. (3) The remote sensor to be used are: SGA MET, SGA GPL.
SEGUGIO CO ACCUMULO
RILEVATORE FUGHE GAS - CO -Rilevatore di monossido di carbonio per uso civile a microprocessore con possibilità di comandare direttamente elettrovalvole, ventole o altri attuatori a 230V~. Rivelazione del monossido di carbonio ad accumulo: simula il comportamento di accumulo del gas nel corpo umano secondo norma EN50291.
SEGUGIO CO ACCUMULATION MODE
GAS LEAKAGE DETECTOR - CO -Microprocessor based domestic carbon monoxide detector with output for cut-off valves, fans or any other electrical actuators with 230V~ power supply. Carbon monoxide detection with accumulation mode: it simulates the gas accumulation in the human body according to standard EN50291.
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORSCaratteristiche tecniche - Technical features
N.O.
COD. RGD COK MP1 € 155
www.seitron.it
RILEVATORI GAS USO RESIDENZIALE - RESIDENTIAL GAS LEAKAGE DETECTORS
Esempio di installazione del SEGUGIO DOUBLE che comanda contemporaneamente un ventilatore per l’allarme da monossido di carbonio e una elettrovalvola per l’allarme da metano.
Installation example of SEGUGIO DOUBLE that simultaneously controls a fan for the alarm from carbon monoxide and a solenoid valve for the alarm from methane.
Elettrovalvola gasGas electro-valve
Segugio Double
(RDX SM1)
Estrattore di ariaAir extractor
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
Tubazione gasGas pipe
www.seitron.it
KIT SEGUGIO METANO
Kit comprendente un Rilevatore SEGUGIO METANO (RGDMETMP1R) alimentato a 230V~, una elettrovalvola a riarmo manuale da 3/4” 230V~ o 12V~ e due riduzioni da 3/4” a 1/2”.
KIT SEGUGIO METHANE
Kit including SEGUGIO METHANE (RGDMETMP1R) gas detector with 230V~ power supply, 1 230V~ or 12V~ cut-off valve with manual reset, 2 x 3/4”to 1/2” nipples.
KIT SEGUGIO GPL
Kit comprendente un Rilevatore SEGUGIO GPL (RGDGPLMP1R) alimentato a 230V~, una elettrovalvola a riarmo manuale da 3/4” 230V~ o 12V~ e due riduzioni da 3/4” a 1/2”.
KIT SEGUGIO LPG
Kit including SEGUGIO LPG (RGDGPLMP1R) gas detector with 230V~ power supply, 1 230V~ or 12V~ cut-off valve with manual reset, 2 x 3/4”to 1/2” nipples.
COD. KD MER 00014 Kit con elettrovalvola N.A. 230V / Kit with N.O. 230V electrovalve € 199
COD. KD MER 00015 Kit con elettrovalvola N.C. 230V / Kit with N.C. 230V electrovalve € 261
COD. KD MER 00008 Kit con elettrovalvola N.A. 12V, basso ass. / Kit with N.O. 12 V low power electrovalve € 209
COD. KD GPR 00017 Kit con elettrovalvola N.A. 230V / Kit with N.O. 230V electrovalve € 199
COD. KD GPR 00018 Kit con elettrovalvola N.C. 230V / Kit with N.C. 230V electrovalve € 261
COD. KD GPR 00016 Kit con elettrovalvola N.A. 12V, basso ass. / Kit with N.O. 12 low power electrovalve € 209
COD. KD GPR 00002 Kit con elettrovalvola N.C. 12V, basso ass. / Kit with N.C. 12 low power electrovalve € 262
www.seitron.it
SGA MET - SGA GPL: Esempi di collegamento / Typical wiring
SENSORE REMOTO METANO O GPL(SOLO PER SEGUGIO)
Sensore remoto per fughe di gas metano o GPL. Elemento sensibile a semiconduttore. Durata sensore: 5 anni. Contenitore IP30.
METHANE OR LPG REMOTE SENSOR (FOR SEGUGIO DETECTORS ONLY)
Remote sensor for methane or LPG gas leakages. Solid state sensing element. Sensor life: 5 years. IP30 case.
SENSORI REMOTI - REMOTE SENSORSCaratteristiche tecniche - Technical features
Alimentazione 6V= .. 12V= dalla centralinaPotenza assorbita 1WUscita Segnale in tensione on/offTipo sensore SnO2 semiconduttoreDurata del sensore 5 anniGas rilevabile Metano o GPLSensibilità impostata 10% L.I.E.Grado di protezione IP30Dimensioni A90 L65 P30mm
Power supply 6V= .. 12V= from detectorPower absorption 1WOutput On/off voltage output Sensor type SnO2 semiconductorSensor life 5 yearsDetectable gas Methane or LPGAlarm threshold 10% L.E.L. IP rating IP30 Dimensions H90 W65 D30mm
SICUREZZA GAS RESIDENZIALE - RESIDENTIAL GAS DETECTORS
COD. SGA MET Metano / Methane € 77
COD. SGA GPL GPL / LPG € 77
www.seitron.it
RDA DA1: Esempi di collegamento / Typical wiring
C02 AIR GUARDIAN
REGOLATORE DI BIOSSIDO DI CARBONIO (CO2)Possibilità di visualizzazione, su display LCD, del livello di CO2 rilevata dal sensore NDIR interno. Uscita con contatti liberi da tensioni, funzione di Test per la verifica del buon funzionamento del regolatore, possibilità di variare le soglie di allarme.
CARBON DIOXIDE CONTROLLER (CO2)Information, on the LCD, of the level of CO2 measured by the NDIR internal sensor. Voltage-free contact output, test function to ensure correct operation of the controller, option to change the alarm thresholds.
SENSORI REMOTI - REMOTE SENSORSCaratteristiche tecniche - Technical features
Alimentazione 230V~/24V 50HzAssorbimento 2,0 VA max.Campo di lettura 0 .. 2000 ppmPrecisione ±30ppmPortata contatti 5(1)A 250V~ SPDT (Liberi da tensione)Grado di protezione IP30Temp. funzionamento 0°C .. 40°C.Temp. stoccaggio - 10°C .. + 50°C.Limiti di umidità 20% .. 80% RH non condensanteDimensioni 132 x 87 x 23,6 (LxAxP)
Power 230V~/24V 50HzAbsorption 2.0 VA max.Detection range 0 .. 2000 ppmAccuracy ±30ppmRated current 5(1)A 250V~ SPDT (Voltage-free)Degree of protection IP30Operating temp 0°C. 40°C.Storage temp - 10°C. + 50°C.Humidity limits 20%. 80% RH non-condensingDimensions 132 x 87 x 23.6 (LxAxP)
COD. RDA DA1 € 420
ACCESSORI - ACCESSORIES
CHM 088 BX
ACM G01ACM M01 D 41 D 41
D 13
Sensore precalibrato sostituibile per rilevatori di gas Metano. Adatto per Segugio e Beagle plus.Precalibrated replaceable gas sensor for Methane gas leakage detectors. Suitable for Segugio and Beagle plus product.
Sensore precalibrato sostituibile per rilevatori di gas GPL. Adatto per Segugio e Beagle plus.Precalibrated replaceable gas sensor for LPG gas leakage detectors. Suitable for Segugio and Beagle plus product.
Bomboletta Gas-Test. Bomboletta per la verifica del funzionamento dei rilevatori gas GPL e metano, con gas non titolato, per ca. 70 test.Gas-Test cylinder.Bump-Test cylinder for LPG and methane gas leakage detectors, for ca. 70 tests.
ACM C01 D 72
Sensore precalibrato sostituibile per rilevatori di CO ad accumulo e soglia. Adatto per Segugio e Beagle. Precalibrated replaceable gas sensor for CO gas leakage detectors with threshold and accumulation mode. Suitable for Segugio and Beagle product.
Sicurezza gas residenziale - Residential gas detectors
SEITRON SPA
36061- Bassano del Grappa (VI) - ItalyVia M. Prosdocimo, 30Tel. +39 0424 567842Fax. +39 0424 [email protected]
ATRP
UB06
36