8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
1/19
Doc: I150IGB01_04.doc 19/12/2003 p. 1 / 19
577
RGK60 RGK60
PROTOCOLLO DI COMUNICAZIONE COMMUNICATION PROTOCOL
MODBUS RTU MODBUS RTU
ADDENDUM ADDENDUM
I150
IGB
0104
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
2/19
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
3/19
Doc: I150IGB01_04.doc 19/12/2003 p. 3 / 19
FUNZIONI MODBUSLe funzioni disponibili sono:
04 = Read inputregister
Consente la lettura dellemisure disponibilinellRGK60 .
06 = Preset singleregister
Permette di modificare iparametri del setup
07 = Read exceptionPermette di leggere lo statodellRGK60
17 = Report slave IDPermette di leggereinformazioni relative
allRGK60
Per esempio, se si vuole leggere dall RGK60 conindirizzo 8 il valore della tensione di linea che sitrova alla locazione 2 (02 Hex), il messaggio daspedire il seguente:
08 04 00 01 00 02 20 92
Dove:08 = indirizzo slave.04 = funzione di lettura locazione.00 01 = indirizzo della locazione diminuito diununit, contenete il valore di tensione media di linea00 02 = numero di registri da leggere a partiredallindirizzo 01.2092 = checksum CRC.
La risposta dell RGK60 la seguente:
08 04 04 00 00 00 64 63 6ADove:08 = indirizzo dell RGK60 (Slave 08).04 = funzione richiesta dal Master.04 = numero di byte inviati dallRGK60 .00 00 00 64 = valore esadecimale della tensione dilinea = 100 V.63 6A = checksum CRC.
FUNZIONE 04: READ INPUT REGISTERLa funzione 04 permette di leggere una o pi
grandezze consecutive in memoria. Lindirizzo diciascuna grandezza e indicato nelle Tabelle 2..7riportate nelle ultime pagine del presente manuale.Come da standard Modbus, lindirizzo specificatonel messaggio va diminuito di 1 rispetto a quelloeffettivo riportato nella tabella.Se lindirizzo richiesto non compreso nella tabella oil numero di registri richiesti maggiore di 20lRGK60 ritorna un messaggio di errore ( veditabella errori).
Richiesta Master:
Indirizzo slave 08h
Funzione 04h
MSB Indirizzo registro 00h
LSB Indirizzo registro 0Fh
MSB Numero registri 00h
LSB Numero registri 08h
MSB CRC 21h
LSB CRC 57h
Nellesempio vengono richiesti allo slave numero 8 n.8 registri consecutivi a partire dallindirizzo 10h.Quindi vengono letti i registri dall 10h al 17h.Ilcomando termina sempre con il valore di checksumCRC.
MODBUS FUNCTIONSThe available functions are:
04 = Read inputregister
Allows to read the RGK60measures.
06 = Preset singleregister
Allows to set the setupparameters
07 = Read exception Allows to read the devicestatus
17 = Report slave IDAllows to read informationabout the RGK60 .
For instance, to read the value of the line voltage,which resides at location 2 (02 Hex) from theRGK60 with serial address 08, the message to sendis the following:
08 04 00 01 00 02 20 92
Whereas:08 = slave address04 = Modbus function Read input register00 01 = Address of the required register (linevoltage) decreased by one00 02 = Number of registers to be read beginningfrom address 00012092 = CRC Checksum
The RGK60 answer is the following:
08 04 04 00 00 00 64 63 6AWhere:08 = RGK60 address (Slave 08)04 = Function requested by the master04 = Number of bytes sent by the RGK6000 00 00 64 = Hex value of the equivalent phase-to-phase voltage (100 V)63 6A = CRC checksum
FUNCTION 04: READ INPUT REGISTERThe Modbus function 04 allows to read one or
more consecutive registers from the slave memory.The address of each measure is given in the tables2..7 reported in the final pages of this manual.
As for Modbus standard, the address in the querymessage must be decreased by one from theeffective address reported in the table.If the measure address is not included in the tableor the number of requested registers exceeds 20the RGK60 will return an error code (see errortable).
Master query:
Slave address 08h
Function 04h
MSB address 00h
LSB address 0Fh
MSB register number 00h
LSB register number 08h
MSB CRC 21h
LSB CRC 57h
In the above example slave 08 is requested for 8consecutive registers beginning with address 10h.Thus, registers from 10h to 17h will be returned. Asusual, the message ends with the CRC checksum.
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
4/19
Doc: I150IGB01_04.doc 19/12/2003 p. 4 / 19
Risposta Slave:
Indirizzo slave 08h
Funzione 04h
Numero di byte 10h
MSB Dato 10h 00h
LSB Dato 10h 00h
--------------------------------------------------- ----
MSB Dato 17h 00h
LSB Dato 17h 00h
MSB CRC 5Eh
LSB CRC 83h
La risposta composta sempre dallindirizzo delloslave, dalla funzione richiesta dal Master e dai datidei registri richiesti. La risposta termina sempre con ilvalore di checksum CRC.
FUNZIONE 06: PRESET SINGLE REGISTERQuesta funzione permette di scrivere nei registri.Essa pu essere utilizzata solo con i registri diindirizzo superiore a 1000 Hex, e solo quando ilmotore e fermo.E possibile ad esempio impostare i parametri delsetup. I parametri di setup modificati vengono
automaticamente salvati nella memoria ritenitiva(eeprom) e qualora il valore impostato non rientri nelvalore minimo e massimo della tabella l RGK60risponder con un messaggio di errore. Se vienerichiesto un parametro ad un indirizzo inesistenteverr risposto con un messaggio di errore. Lindirizzoed il range valido per i vari parametri pu esseretrovato nelle Tabelle 5, 6 e 7.Con la funzione 06 e inoltre possibile eseguire deicomandi utilizzando gli indirizzi ed i valori riportatinella Tabella 4.
Richiesta Master:
Indirizzo slave 08h
Funzione 06h
MSB Indirizzo registro 21h
LSB Indirizzo registro 04h
MSB Dato 01h
LSB Dato 90h
MSB CRC C3h
LSB CRC 52h
Nellesempio viene richiesto di modificare ilparametro P0204 allindirizzo 2105 Hex ( tensionenominale ) con il valore 400.
Risposta Slave:La risposta un eco della domanda, cio vieneinviato al master lindirizzo del dato da modificare e ilnuovo valore del parametro.
Slave response:
Slave address 08h
Function 04h
Byte number 10h
MSB register 10h 00h
LSB register 10h 00h
--------------------------------------------------- ----
MSB register 17h 00h
LSB register 17h 00h
MSB CRC 5Eh
LSB CRC 83h
The response is always composed of the slaveaddress, the function code requested by the masterand the contents of the requested registers. Theanswer ends with the CRC.
FUNCTION 06: PRESET SINGLE REGISTERThis function allows to write in the registers.It can be used only with registers with addresshigher than 1000 Hex, and only when the motor isstopped.For instance it is possible to change setupparameters. Modified parameters are automatically
saved in the non-volatile eeprom memory. If thevalue is not in the correct range, the RGK60 willanswer with an error message. In the same way, ifthe parameter address is not recognised, theRGK60 will send an error response.The address and the valid range for each parameterare indicated in Tables 5, 6 and 7.With function 06, some commands can be possiblyexecuted sending the addresses and the valuesreported in Table 4.
Master message:
Slave address 08h
Function 06h
MSB register address 21h
LSB register address 04h
MSB data 01h
LSB data 90h
MSB CRC C3h
LSB CRC 52h
In the above message, the master wants to setparameter P0204 at address 2105 Hex (NominalVoltage) with value 400.
Slave response:The slave response is an echo to the query, that isthe slave sends back to the master the address andthe new value of the variable.
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
5/19
Doc: I150IGB01_04.doc 19/12/2003 p. 5 / 19
FUNZIONE 07: READ EXCEPTION STATUSTale funzione permette di leggere lo stato in cui sitrova lRGK60.
Richiesta Master:
Indirizzo slave 08h
Funzione 07h
MSB CRC 47h
LSB CRC B2h
La tabella seguente riporta il significato del byteinviato dall RGK60 come risposta:
BIT SIGNIFICATO
0 Reset/OFF mode
1 Man mode
2 Aut mode
3 Test mode
4 Status Rete
5 Status generatore
6 Status motore
7 Status teleruttore rete
8 Status teleruttore generatore
9 Status Allarme
FUNZIONE 17: REPORT SLAVE IDQuesta funzione permette di identificare il tipo diRGK60.
Richiesta Master.
Indirizzo slave 08h
Funzione 11h
MSB CRC C6h
LSB CRC 7Ch
Risposta Slave:
Indirizzo slave 08h
Funzione 11h
Numero byte 06h
Dato 1 (Rev. Software) 11h
Dato 2 (Rev. hardware) 02h
Dato 3 (Rev. Testi) 0Ah
Dato 4 (Rev. Parametri) 08h
Dato 5 (Mod. Scheda Slot A) 01h
Dato 6 (Mod. Scheda Slot B) 15h
MSB CRC F3h
LSB CRC 34h
ERRORINel caso lo slave riceva un messaggio errato,segnala la condizione al master rispondendo con unmessaggio composto dalla funzione richiesta in ORcon 80 Hex, seguita da un codice di errore.Nella seguente tabella vengono riportati i codici dierrore inviati dallo slave al master
TABELLA 1: CODICI ERRORE
COD ERRORE
01 Funzione non valida
02 Indirizzo registro illegale
03 Valore del parametro fuori range
04 Impossibile effettuare operazione
06Slave occupato, funzionemomentaneamente non disponibile (es.motore in marcia)
FUNCTION 07: READ EXCEPTION STATUSThis function allows to read the status of theRGK60.
Master query:
Slave address 08h
Function 07h
MSB CRC 47h
LSB CRC B2h
The following table gives the meaning of the statusbyte sent by the RGK60 as answer:
BIT MEANING
0 Reset/OFF mode
1 Man mode
2 Aut mode
3 Test mode
4 Mains status
5 Generator status
6 Motor status
7 Mains breaking status
8 Generator breaking status
9 Alarm status
FUNZIONE 17: REPORT SLAVE IDThis function allows to identify the RGK60 type.
Master query.
Slave address 08h
Function 11h
MSB CRC C6h
LSB CRC 7Ch
Slave response:
Slave address 08h
Function 11h
Byte number 06h
Data 1Sotware revision) 11h
Data 2 (Hardware revision) 02h
Data 3 (Labels revision) 0Ah
Data 4 (Parameters revision) 08h
Dato 5 (Mod. Interface Slot A) 01h
Dato 6 (Mod. Interface Slot B) 15h
MSB CRC F3h
LSB CRC 34h
ERRORSIn case the slave receives an incorrect message, itanswers with a massage composed by the queriedfunction ORed with 80 Hex, followed by an errorcode byte.In the following table are reported the error codessent by the slave to the master:
TABLE 1: ERROR CODES
CODE ERROR
01 Invalid function
02 Invalid address
03 Parameter out of range
04 Function execution impossible
06Slave busy, function momentarily notavailable (e.g. motor is running)
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
6/19
Doc: I150IGB01_04.doc 19/12/2003 p. 6 / 19
Algoritmo di calcolo del CRCCRC calculation algorithm
CALCOLO DEL CRC (CHECKSUM)
Esempio di calcolo:
Frame = 0207h
Inizializzazione CRC 1111 1111 1111 1111Carica primo byte 0000 0010Esegue xor con il primo 1111 1111 1111 1101Byte della frameEsegue primo shift a dx 0111 1111 1111 1110 1
Carry=1,carica polinomio 1010 0000 0000 0001Esegue xor con il 1101 1111 1111 1111polinomioEsegue secondo shift dx 0110 1111 1111 1111 1Carry=1,carica polinomio 1010 0000 0000 0001Esegue xor con il 1100 1111 1111 1110polinomioEsegue terzo shift 0110 0111 1111 1111 0Esegue quarto shift 0011 0011 1111 1111 1Carry=1, carica polinomio 1010 0000 0000 0001Esegue xor con il 1001 0011 1111 1110PolinomioEseque quinto shift dx 0100 1001 1111 1111 0Eseque sesto shift dx 0010 0100 1111 1111 1Carry=1, carica polinomio 1010 0000 0000 0001Esegue xor con polinomio 1000 0100 1111 1110
Esegue settimo shift dx 0100 0010 0111 1111 0Esegue ottavo shift dx 0010 0001 0011 1111 1Carry=1, carica polinomio 1010 0000 0000 0001
Carica secondo byte 0000 0111della frameEsegue xor con il 1000 0001 0011 1001Secondo byte della frameEsegue primo shift dx 0100 0000 1001 1100 1Carry=1, carica polinomio 1010 0000 0000 0001Esegue xor con il 1110 0000 1001 1101polinomioEsegue secondo shift dx 0111 0000 0100 1110 1Carry=1, carica polinomio 1010 0000 0000 0001Esegue xor con il 1101 0000 0100 1111
polinomioEsegue terzo shift dx 0110 1000 0010 0111 1Carry=1, carica polinomio 1010 0000 0000 0001Esegue xor con il 1100 1000 0010 0110polinomioEsegue quarto shift dx 0110 0100 0001 0011 0Esegue quinto shift dx 0010 0100 0000 1001 1Carry=1, carica polinomio 1010 0000 0000 0001Esegue xor con il 1001 0010 0000 1000polinomioEsegue sesto shift dx 0100 1001 0000 0100 0Esegue settimo shift dx 0010 0100 1000 0010 0Esegue ottavo shift dx 0001 0010 0100 0001 0Risultato CRC 0001 0010 0100 0001
12h 41h
Nota:Il byte 41h viene spedito per primo (anche see il LSB), poi viene trasmesso 12h.
CRC CALCULATION (CHECKSUM)
Example of CRC calculation:
Frame = 0207h
CRC initialization 1111 1111 1111 1111Load the first byte 0000 0010Execute xor with the first 1111 1111 1111 1101Byte of the frameExecute 1st right shift 0111 1111 1111 1110 1
Carry=1,load polynomial 1010 0000 0000 0001Execute xor with the 1101 1111 1111 1111polynomialExecute 2ndright shift 0110 1111 1111 1111 1Carry=1,load polynomial 1010 0000 0000 0001Execute xor with the 1100 1111 1111 1110polynomialExecute 3rd right shift 0110 0111 1111 1111 0Execute 4thright shift 0011 0011 1111 1111 1Carry=1,load polynomial 1010 0000 0000 0001Execute xor with the 1001 0011 1111 1110polynomialExecute 5thright shift 0100 1001 1111 1111 0Execute 6thright shift 0010 0100 1111 1111 1Carry=1,load polynomial 1010 0000 0000 0001Execute xor with the 1000 0100 1111 1110
polynomialExecute 7th right shift 0100 0010 0111 1111 0Execute 8th right shift 0010 0001 0011 1111 1Carry=1,load polynomial 1010 0000 0000 0001
Load the second byte 0000 0111of the frameExecute xor with the 1000 0001 0011 1001Second byte of the frameExecute 1st right shift 0100 0000 1001 1100 1Carry=1,load polynomial 1010 0000 0000 0001Execute xor with the 1110 0000 1001 1101polynomialExecute 2ndright shift 0111 0000 0100 1110 1
Carry=1,load polynomial 1010 0000 0000 0001Execute xor with the 1101 0000 0100 1111
polynomialExecute 3rdright shift 0110 1000 0010 0111 1Carry=1,load polynomial 1010 0000 0000 0001Execute xor with the 1100 1000 0010 0110polynomialExecute 4thright shift 0110 0100 0001 0011 0Execute 5thright shift 0010 0100 0000 1001 1Carry=1,load polynomial 1010 0000 0000 0001Execute xor with the 1001 0010 0000 1000polynomialExecute 6thright shift 0100 1001 0000 0100 0Execute 7thright shift 0010 0100 1000 0010 0Execute 8thright shift 0001 0010 0100 0001 0CRC Result 0001 0010 0100 0001
12h 41h
Note:The byte 41h is sent first(even if it is theLSB), then12h is sent.
CRC xor BYTE = CRC
n = 0
CRC right shift
carry over
CRC xor POLY = CRC
n = n + 1
next BYTE
end message
End
n > 7
Hex FFFF = CRC
no
no
yes
yes
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
7/19
Doc: I150IGB01_04.doc 19/12/2003 p. 7 / 19
TABELLA 2: TABLE 2:MISURE FORNITE DAL PROTOCOLLO DI COMUNICAZIONE MEASURES SUPPLIED BY SERIAL COMMUNICATION PROTOCOL
(Utilizzabili con funzione 04) (To be used with function 04)
INDIRIZZOADDRESS
WORDS MISURA MEASURE UNITAUNIT FORMATOFORMAT
02h 2 Tensione di fase rete L1 Mains phase voltage L1 V Unsigned long
04h 2 Tensione di fase rete L2 Mains phase voltage L2 V Unsigned long
06h 2 Tensione di fase rete L3 Mains phase voltage L3 V Unsigned long
08h 2 Tensione di linea rete L1-L2 Mains phase to phase voltage L1-L2 V Unsigned long
0Ah 2 Tensione di linea rete L2-L3 Mains phase to phase voltage L2-L3 V Unsigned long
0Ch 2 Tensione di linea rete L3-L1 Mains phase to phase voltage L3-L1 V Unsigned long
0Eh 2 Tensione di fase generatore L1 Generator phase voltage L1 V Unsigned long
10h 2 Tensione di fase generatore L2 Generator phase voltage L2 V Unsigned long
12h 2 Tensione di fase generatore L3 Generator phase voltage L3 V Unsigned long
14h 2 Tensione di linea generatore L1-L2 Generator phase to phase voltage L1-L2 V Unsigned long
16h 2 Tensione di linea generatore L2-L3 Generator phase to phase voltage L2-L3 V Unsigned long
18h 2 Tensione di linea generatore L3-L1 Generator phase to phase voltage L3-L1 V Unsigned long
1Ah 2 Corrente L1 Current L1 A Unsigned long
1Ch 2 Corrente L2 Current L2 A Unsigned long
1Eh 2 Corrente L3 Current L3 A Unsigned long
20h 2 Potenza attiva rete L1 Mains active power L1 W Unsigned long22h 2 Potenza attiva rete L2 Mains active power L2 W Unsigned long
24h 2 Potenza attiva rete L3 Mains active power L3 W Unsigned long
26h 2 Potenza reattiva rete L1 Mains reactive power L1 Var Unsigned long28h 2 Potenza reattiva rete L2 Mains reactive power L2 Var Unsigned long2Ah 2 Potenza reattiva rete L3 Mains reactive power L3 Var Unsigned long2Ch 2 Potenza apparente rete L1 Mains apparent power L1 VA Unsigned long
2Eh 2 Potenza apparente rete L2 Mains apparent power L2 VA Unsigned long
30h 2 Potenza apparente rete L3 Mains apparent power L3 VA Unsigned long
32h 2 Potenza attiva generatore L1 Generator active power L1 W Unsigned long
34h 2 Potenza attiva generatore L2 Generator active power L2 W Unsigned long
36h 2 Potenza attiva generatore L3 Generator active power L3 W Unsigned long
38h 2 Potenza reattiva generatore L1 Generator reactive power L1 Var Unsigned long3Ah 2 Potenza reattiva generatore L2 Generator reactive power L2 Var Unsigned long3Ch 2 Potenza reattiva generatore L3 Generator reactive power L3 Var Unsigned long3Eh 2 Potenza apparente generatore L1 Generator apparent power L1 VA Unsigned long
40h 2 Potenza apparente generatore L2 Generator apparent power L2 VA Unsigned long
42h 2 Potenza apparente generatore L3 Generator apparent power L3 VA Unsigned long
44h 2 Potenza attiva totale di rete Mains total active power W Unsigned long
46h 2 Potenza reattiva totale di rete Mains total reactive power Var Unsigned long
48h 2 Potenza apparente totale di rete Mains total apparent power VA Unsigned long
4Ah 2 Potenza attiva totale di generatore Generator total active power W Unsigned long
4Ch 2 Potenza reattiva totale di generatore Generator total reactive power Var Unsigned long
4Eh 2 Potenza apparente totale di generatore Generator total apparent power VA Unsigned long
50h 2 Fattore di potenza rete L1 Mains power factor L1 Unsigned long
52h 2 Fattore di potenza rete L2 Mains power factor L2 Unsigned long
54h 2 Fattore di potenza rete L3 Mains power factor L3 Unsigned long
56h 2 Fattore di potenza totale rete Mains totla power factor Unsigned long
58h 2 Fattore di potenza generatore L1 Generator power factor L1 Unsigned long
5Ah 2 Fattore di potenza generatore L2 Generator power factor L2 Unsigned long
5Ch 2 Fattore di potenza generatore L3 Generator power factor L3 Unsigned long
5Eh 2 Fattore di potenza totale generatore Generator totla power factor Unsigned long
60h 2 Energia attiva rete Mains total active energy Kwh*10 Unsigned long
62h 2 Energia reattiva rete Mains total reactive power Kvarh*10 Unsigned long
64h 2 Energia attiva generatore Generator total active energy Kwh*10 Unsigned long
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
8/19
Doc: I150IGB01_04.doc 19/12/2003 p. 8 / 19
66h 2 Energia reattiva generatore Generator total reactive energy Kvarh*10 Unsigned long
68h 2 Frequenza di rete Mains frequency Hz*10 Unsigned long
6Ah 2 Frequenza di generatore Generator frequency Hz*10 Unsigned long
6Ch 2 Velocit W Speed W Rpm/min Unsigned long
6Eh 2 Velocit calcolata della frequenza generatore Speed calculated from generator frequency Rpm/min Unsigned long
70h 2 Velocit Pick-UP Sensor Speed Pick-UP Rpm/min Unsigned long
72h 2 Temperatura Temperature C o F Unsigned long
74h 2 Pressione Pression Bar o psi * 100 Unsigned long
76h 2 Carburante Fuel % Unsigned long
78h 2 Batteria Battery V Unsigned long
TABELLA 3: TABLE 3:BIT DI STATO STATUS BITS
(Utilizzabili con funzione 04) (To be used with function 04)
INDIRIZZOADDRESS
WORDS MISURA MEASURE UNITAUNIT FORMATOFORMAT
160h 2 Stato bits di errore Error bits status (bit) Unsigned long
162h 2 Stato bits di errore Error bits status (bit) Unsigned long
170h 2 Uscite standard + espansioni Standard output + expansion (bit) Unsigned long
180h 2Ingressi standard + espansioni (tutteprogrammabili)
Standard input + expansion (allprogrammable)
(bit) Unsigned long
190h 2 Status Status (bit) Unsigned long
Leggendo la word allindirizzo 160h vengono restituiti 32 bit con significato come da tabella:Reading the word starting at address 160h will return 32 bits with the following meaning:
Bit Codice Allarme Code Alarm
0 A01 Preallarme temperatura motore (sensore analogico) A01 Engine temperature warning (analog sensor)
1 A02 Alta temperatura motore (sensore analogico) A02 High engine temperature (analog sensor)
2 A03 Guasto sensore analogico temperatura A03 Temperature analog sensor fault
3 A04 Alta temperatura motore (sensore digitale) A04 High engine temperature (digital sensor)
4 A05 Preallarme pressione olio (sensore analogico) A05 Oil pressure warning (analog sensor)
5 A06 Bassa pressione olio (sensore analogico) A06 Low oil pressure (analog sensor)
6 A07 Guasto sensore analogico pressione A07 Pressure analog sensor fault
7 A08 Bassa pressione olio (sensore digitale) A08 Low oil pressure (digital sensor)
8 A09 Guasto sensore digitale pressione A09 Pressure digital sensor fault
9 A10 Preallarme livello carburante (sensore analogico) A10 Fuel level warning (analog sensor)
10 A11 Basso livello carburante (sensore analogico) A11 Low fuel level (analog sensor)
11 A12 Guasto sensore analogico livello A12 Level analog sensor fault
12 A13 Basso livello carburante (sensore digitale) A13 Low fuel level (digital sensor)
13 A14 Tensione batteria alta A14 High battery voltage
14 A15 Tensione batteria bassa A15 Low battery voltage
15 A16 Batteria inefficiente A16 Inefficient battery
16 A17 Avaria alternatore carica batteria A17 Charger alternator failure
17 A18 Avaria segnale W A18 W signal failure
18 A19 Bassa velocit motore W A19 Low engine W speed
19 A20 Alta velocit motore W A20 High engine W speed
20 A21 Mancato avviamento A21 Starting failure
21 A22 Arresto di emergenza A22 Emergency stop
22 A23 Arresto inaspettato A23 Unexpected stop
23 A24 Mancato arresto A24 Engine stop failure
24 A25 Bassa frequenza generatore A25 Low generator frequency
25 A26 Alta frequenza generatore A26 High generator frequency26 A27 Bassa tensione generatore A27 Low generator voltage
27 A28 Alta tensione generatore A28 High generator voltage
28 A29 Asimmetria generatore A29 Generator asymmetry
29 A30 Corto circuito generatore A30 Generator short-circuit
30 A31 Sovraccarico generatore A31 Generator overload
31 A32 Intervento protezione esterna generatore A32 External generator protection tripping
Leggendo la word allindirizzo 162h vengono restituiti 32 bit con significato come da tabella:Reading the word starting at address 162h will return 32 bits with the following meaning:Bit Codice Allarme Code Alarm
0 A33 Errata sequenza fasi generatore A33 Incorrect generator phase sequence
1 A34 Errata sequenza fasi rete A34 Incorrect mains phase sequence
2 A35 Errata impostazione frequenza di sistema A35 Wrong system frequency setting
3 A36 Anomalia contattore generatore A36 Generator contactor failure4 A37 Anomalia contattore rete A37 Mains contactor failure
5 A38 Richiesta manutenzione A38 Maintenance requested
6 A39 Errore di sistema A39 System error
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
9/19
Doc: I150IGB01_04.doc 19/12/2003 p. 9 / 19
7 A40 Serbatoio travaso vuoto A40 Fuel transfer empty
8 A41 Serbatoio travaso troppo pieno A41 Fuel transfer too full
9 A42 Ore di noleggio esaurite A42 Rent hours exhausted
10 A43 Basso livello liquido radiatore A43 Low radiator liquid level
11 A44 Interruttore chiuso A44 Circuit breaker closed
12 A45 Interruttore aperto A45 Circuit breaker open
13 U01 Allarme utente 1 U01 Users alarm 1
14 U02 Allarme utente 2 U02 Users alarm 2
15 U03 Allarme utente 3 U03 Users alarm 3
16 U04 Allarme utente 4 U04 Users alarm 4
17 U05 Allarme utente 5 U05 Users alarm 518 U06 Allarme utente 6 U06 Users alarm 6
19 U07 Allarme utente 7 U07 Users alarm 7
20 U08 Allarme utente 8 U08 Users alarm 8
21-31 Bit liberi 21-31 Free bits
Leggendo la word allindirizzo 170h vengono restituiti 32 bit con significato come da tabella:Reading the word starting at address 170h will return 32 bits with the following meaning:
Leggendo la word allindirizzo 180h vengono restituiti 32 bit con significato come da tabella:Reading the word starting at address 180h will return 32 bits with the following meaning:
Leggendo la word allindirizzo 190h vengono restituiti 32 bit con significato come da tabella:Reading the word starting at address 190h will return 32 bits with the following meaning:
Bit Significato Meaning
0 Teleruttore rete Mains contactor
1 Teleruttore generatore Generator contactor
2 Uscita programmabile 1 Programmable output 1
3 Uscita programmabile 2 Programmable output 2
4 Uscita programmabile 3 Programmable output 3
5 Motore Start Motor Start6 Uscita programmabile 4 Programmable output 4
7 Uscita elettrovalvola carburante Fuel valve output
8 Uscita programmabile 1 espansione Expansion Programmable output 1
9 Uscita programmabile 2 espansione Expansion Programmable output 2
10 Uscita programmabile 3 espansione Expansion Programmable output 3
11 Uscita programmabile 4 espansione Expansion Programmable output 4
12 Uscita programmabile 5 espansione Expansion Programmable output 5
13 Uscita programmabile 6 espansione Expansion Programmable output 6
14 Uscita programmabile 7 espansione Expansion Programmable output 7
15 Uscita programmabile 8 espansione Expansion Programmable output 8
16 Uscita programmabile 9 espansione Expansion Programmable output 9
17 Uscita programmabile 10 espansione Expansion Programmable output 10
18 Uscita programmabile 11 espansione Expansion Programmable output 11
19 Uscita programmabile 12 espansione Expansion Programmable output 12
20..31 Bit liberi Free bits
Bit Significato Meaning
0 Ingresso programmabile 1 Programmable input 1
1 Ingresso programmabile 2 Programmable input 2
2 Ingresso programmabile 3 Programmable input 3
3 Ingresso programmabile 4 Programmable input 4
4 Ingresso programmabile 5 Programmable input 5
5 Ingresso programmabile 6 Programmable input 6
6 Ingresso programmabile 7 Programmable input 7
7 Ingresso programmabile 8 Programmable input 8
8 Ingresso programmabile 9 Programmable input 9
9 Ingresso programmabile 10 Programmable input 10
10 Ingresso programmabile 11 Programmable input 11
11 Ingresso programmabile 12 Programmable input 1212 Ingresso programmabile espansione 1 Expansion programmable input 1
13 Ingresso programmabile espansione 2 Expansion programmable input 2
14 Ingresso programmabile espansione 3 Expansion programmable input 3
15 Ingresso programmabile espansione 4 Expansion programmable input 4
16 Ingresso programmabile espansione 5 Expansion programmable input 5
17 Ingresso programmabile espansione 6 Expansion programmable input 6
18 Ingresso programmabile espansione 7 Expansion programmable input 7
19 Ingresso programmabile espansione 8 Expansion programmable input 8
20 Ingresso programmabile espansione 9 Expansion programmable input 9
21 Ingresso programmabile espansione 10 Expansion programmable input 10
22 Ingresso programmabile espansione 11 Expansion programmable input 11
23 Ingresso programmabile espansione 12 Expansion programmable input 12
24 Ingresso programmabile espansione 13 Expansion programmable input 13
25 Ingresso programmabile espansione 14 Expansion programmable input 14
26-31 liberi free
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
10/19
Doc: I150IGB01_04.doc 19/12/2003 p. 10 / 19
Bit Significato Meaning
0 Allarme Alarm
1 Motore Start Motor Start
2 Motore Stop Motor Stop
3 Raffreddamento Cooling
4 Test Test
5 Strat esterno External Strat
6 Stop esterno External Stop
7 Start per soglia kw Start kw trip
8 Start EJP Start EJP
9 Start SCR Start SCR10..31 Bit liberi Free bits
TABELLA 4: TABLE 4:COMANDI COMMANDS(Utilizzabili con funzione 06) (To be used with function 06)
INDIRIZZOADDRESS
WORDS FUNZIONE FUNCTION FORMATOFORMAT
1000h 1 Modalit OFF Operating mode OFF Unsigned integer
1001h 1 Modalit MAN Operating mode MAN Unsigned integer
1002h 1 Modalit AUT Operating mode AUT Unsigned integer
1003h 1 Modalit TEST Operating mode TEST Unsigned integer
1004h 1 Chiusura / Apertura teleruttore rete Opening / Closing mains contactor Unsigned integer
1005h 1 Chiusura / Apertura teleruttore generatore Opening / Closing generator contactor Unsigned integer
1006h 1 Start motore Motor start Unsigned integer
1007h 1 Stop motore Motor stop Unsigned integer
1100h 1 Scrittura tutta memoria eeprom Write all memory eeprom Unsigned integer
1200h 1 Menu comandi Command menu Unsigned integer
Per eseguire il comando e necessario usare la funzione 06 Preset single registere scrivere il valore 0001 hex allindirizzo specificato.To execute the command the user must use the function 06 Preset single register, writing value 0001Hex to the address specified..
Per eseguire una delle funzioni disponibili nel menu comandi e necessario scrivere il valore 00xx Hex allindirizzo 1200, dove xx rappresenta il numero della vocedel menu comandi. Ad esempio per eseguire il comando C02 Reset ore manutenzionesara necessario scrivere il valore 0002 Hex allindirizzo 1200 Hexutilizzando la funzione Modbus 06. Per la lista delle funzioni disponibili nel menu comandi fare riferimento al manuale operativo.To execute one of the functions available in the Command menu it is necessary to write value 00xxHex to address 1200 Hex, where xx represents the number of
the command menu item. For instance, to execute the command C.02 Maintenance hour reset , the user must write value 0002 hex to the address 1200 hex usingModbus function 06. See the operating manual for the complete list of the command menu functions.
IMPOSTAZIONE PARAMETRITramite il protocollo Modbus e possibile accedere ai parametri dei menubase, esteso e funzioni. Nelle seguenti tabelle e riportato il range diimpostazione in formato numerico. Per interpretare correttamente lacorrispondenza fra valore numerico e funzione selezionata e/o unita dimisura, fare riferimento al manuale operativo dellRGK60 .I seguenti parametri sono sempre disponibili in lettura, mentrepossono essere modificati solo quando lo strumento in modalitOFF.
PARAMETER SETTINGUsing the Modbus protocol it is possible to access the base, advanced andfunction menu parameters. In the following tables it is reported the numericalrange for each parameter. To correctly understand the correspondencebetween the numeric value and the selected function and/or the unit ofmeasure, please see the RGK60 operating manual.The following parameters can be read at any time, while the write-access is possible only when the RGK60 is OFF mode.
PARAMETRI MENU UTILITA UTILITY PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO PARAMETER RANGE FORMATOFORMAT
2002h 1 P0101 Lingue English/Italiano/Francais/Pourtugues/Espanol
P0101 Languages Unsigned integer
2003h 1 P0102 Anno 1989-2089 P0102 Year Unsigned integer
2004h 1 P0103 Mese 1-12 P0103 Month Unsigned integer
2005h 1 P0104 Giorno Mese 1-31 P0104 Day of the month Unsigned integer
2006h 1 P0105 Giorno Settimana 1-7 P0105 Day of the week Unsigned integer
2007h 1 P0106 Ora 0-23 P0106 Hour Unsigned integer
2008h 1 P0107 Minuti 0-59 P0107 Minutes Unsigned integer
2009h 1 P0108 Secondi 0-59 P0108 Seconds Unsigned integer
200Ah 1 P0109 Set orologio allalimentazione OFF/ON P0109 Clock setting at power-up Unsigned integer
200Bh 1 P0110 Ritorno pagina principale (sec) OFF/5-999 P0110 Default page return (sec) Unsigned integer
200Ch 1 P0111 Contrasto display (%) 0-100 P0111 Display contrast (%) Unsigned integer
200Dh 1 P0112 Retroilluminazione dispaly (%) 0-100 P0112 Display Backlight (%) Unsigned integer
200Eh 1P0113 Ritardo spegnimento (min)retroilluminazione
OFF/1-900 P0113 Delay backlight off (min) Unsigned integer
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
11/19
Doc: I150IGB01_04.doc 19/12/2003 p. 11 / 19
PARAMETRI MENU GENERALI GENERAL PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2102h 1 P0201 Rapporto TA 1.0-2000.0 P0201 CT ratio Unsigned integer
2103h 1 P0202 Rapporto TV 1.0-500.0 P0202 VT ratio Unsigned integer
2104h 1 P0203 Tipo di collegamento 3N-3-2N-1N P0203 Wiring configuration Unsigned integer
2105h 1 P0204 Tensione nominale (V) 100-50000 P0204 Rated voltage (V) Unsigned integer
2106h 1 P0205 Frequenza (Hz) 50/60 P0205 Frequency (Hz) Unsigned integer
2107h 1 P0206 Rapporto RPM / W 0.001-50.000 P0206 RPM / W ratio Unsigned integer
2108h 1 P0207 Giri nominale Motore (RPM) 750-3600 P0207 Rated engine speed (RPM) Unsigned integer
2109h 1 P0208 Scelta unit di misura C/bar-F/psi P0208 Unit of measure Unsigned integer
210Ah 1 P0209 Interbloccco rete/generatore (sec) 0.0-60.0 P0209 MAINS/GEN interlock (sec) Unsigned integer
210Bh 1P0210 Ritardo ON/OFF rete/generatore(sec)
1-60 P0210 M/G feedback delay (sec) Unsigned integer
210Ch 1 P0211 Modo OFF/RESET allalimentazione OFF/ON P0211 RESET mode at power-up Unsigned integer
210Dh 1 P0212 Tempo sirena (sec) OFF/1-60 P0212 Siren time (sec) Unsigned integer
210Eh 1 P0213 Sirena prima di avviamento (sec) OFF/1-60 P0213 Siren before starting (sec) Unsigned integer
210Fh 1 P0214 Sirena PC in linea (sec OFF/1-60 P0214 Siren PC on line (sec) Unsigned integer
2110h 1 P0215 Capacit serbatoio OFF/1-30000 P0215 Fuel capacity Unsigned integer
PARAMETRI MENU BATTERIA BATTERIA PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2202h 1 P0301 Tensione batteria (V) 1.0-2000.0 P0301 Battery voltage (V) Unsigned integer
2203h 1 P0302 Limite tensione MAX (%) 1.0-500.0 P0302 MAX voltage limit (%) Unsigned integer2204h 1 P0303 Limite tensione MIN (%) 3N-3-2N-1N P0303 MIN voltage limit (%) Unsigned integer
2205h 1 P0304 Ritardo tensione MIN/MAX (sec) 100-50000 P0304 MIN/MAX voltage delay (sec) Unsigned integer
PARAMETRI MENU AVVIAMENTO MOTORE ENGINE START PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2302h 1P0401 Tensione alternatore motore avviato(V)
OFF/3-30 P0401 Alternator voltage engine started (V) Unsigned integer
2303h 1P0402 Tensione generatore motore avviato(%)
OFF/10-100% P0402 Generator voltage engine started (%) Unsigned integer
2304h 1P0403 Frequenza generatore motoreavviato (%)
OFF/10-100% P0403 Generator frequency engine started(%)
Unsigned integer
2305h 1 P0404 Segnale W motore avviato (RPM) OFF/10-100% P0404 W signal engine started (RPM) Unsigned integer
2306h 1 P0405 Preriscaldo candelette (sec) OFF/1-60 P0405 Glow-plugs preheating (sec) Unsigned integer
2307h 1 P0406 Numero tentativi avviamento 1-10 P0406 Starting attempts number Unsigned integer
2308h 1 P0407 Durata tentativo avv. (sec) 1-30 P0407 Attempts starting time (sec) Unsigned integer
2309h 1 P0408 Pausa tentativi avviamento (sec) 1-30 P0408 Pause between starting (sec) Unsigned integer
230Ah 1P0409 Pausa avviamento interrotto esuccessivo (sec)
OFF/1-20 P0409 Aborted starting & subsequent (sec) Unsigned integer
230Bh 1 P0410 Tempo decelerazione (sec) OFF/1-180 P0410 Deceleration time (sec) Unsigned integer
230Ch 1 P0411 Tempo raffreddamento (sec) 1-3600 P0411 Cooling time (sec) Unsigned integer
230Dh 1 P0412 Tempo magnete arresto (sec) OFF/1-60 P0412 Stop magnet time (sec) Unsigned integer
230Eh 1 P0413 Ritardo valvola gas (sec) OFF/1-10 P0413 Gas valve delay (sec) Unsigned integer
230Fh 1 P0414 Tempo cicchetto (sec) OFF/1-10 P0414 Priming time (sec) Unsigned integer
2310h 1 P0415 Tempo valvola aria (sec) OFF/1-10 P0415 Choke valve time (sec) Unsigned integer
2311h 1 P0416 Limite stacco aria (%) 0-100 P0416 Choke OFF limit (%) Unsigned integer
PARAMETRI MENU CONTROLLO MOTORE ENGINE CONTROL PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2402h 1 P0501 Scelta sensore pressione (1) P0501 Pressure sensor selection Unsigned integer
2403h 1 P0502 Scelta sensore temperatura (1) P0502 Temperature sensor selection Unsigned integer
2404h 1 P0503 Scelta sensore carburante (1) P0503 Fuel sensor selection Unsigned integer
2405h 1 P0504 Preallarme pressione MIN 0.1-180.0 P0504 MIN pressure warning Unsigned integer
2406h 1 P0505 Limite pressione MIN 0.1-180.0 P0505 MIN pressure limit Unsigned integer
2407h 1 P0506 Preallarme temperatura MAX 40-285 P0506 MAX temperature warning Unsigned integer
2408h 1 P0507 Limite temperatura MAX 40-285 P0507 MAX temperature limit Unsigned integer
2409h 1 P0508 Preallarme carburante MIN (%) 0-100 P0508 MIN fuel warning (%) Unsigned integer
240Ah 1 P0509 Livello carburante MIN (%) 0-100 P0509 MIN fuel level (%) Unsigned integer
240Bh 1P0510 Inibizione allarmi allavviamento(sec)
1-30 P0510 Alarms inhibition at starting (sec) Unsigned integer
240Ch 1 P0511 Limite velocit W MAX (%) 100-120 P0511 MAX W speed limit (%) Unsigned integer
240Dh 1 P0512 Ritardo velocit W MAX (sec) 3-20 P0512 MAX W speed delay (sec) Unsigned integer
240Eh 1 P0513 Limite velocit W MIN (%) 80-100 P0513 MIN W speed limit (%) Unsigned integer240Fh 1 P0514 Ritardo velocit W MIN (sec) 0-600 P0514 MIN W speed delay (sec) Unsigned integer
2410h 1 P0515 Ritardo A03 (min) OFF/1-60 P0515 Delay A03 (min) Unsigned integer
(1) Prima di impostare il tipo di sensore, verificare la curva di risposta mediante il software di set-up.(1) Before setting the type of sensor, it i s advisable to check the curve characteristic by means of the set-up software
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
12/19
Doc: I150IGB01_04.doc 19/12/2003 p. 12 / 19
PARAMETRI MENU CONTROLLO RETE MAINS CONTROL PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2502h 1 P0601 Limite tensione MIN (%) 70-100 P0601 MIN voltage limit (%) Unsigned integer
2503h 1 P0602 Ritardo tensione MIN (sec) 0-600 P0602 MIN voltage delay (sec) Unsigned integer
2504h 1 P0603 Limite tensione MAX (%) 100-120 P0603 MAX voltage limit (%) Unsigned integer
2505h 1 P0604 Ritardo tensione MAX (sec) 0-600 P0604 MAX voltage delay (sec) Unsigned integer
2506h 1 P0605 Ritardo rete nei limiti (sec) 1-600 P0605 MAINS into limits delay(sec) Unsigned integer
2507h 1 P0606 Isteresi limiti MIN/MAX (%) 0.0-5.0 P0606 MIN/MAX hysteresis limits (%) Unsigned integer
2508h 1 P0607 Limite asimmetria MAX (%) 5-20 P0607 MAX asymmetry limit (%) Unsigned integer
2509h 1 P0608 Ritardo asimmetria MAX (sec) 0-600 P0608 MAX asymmetry delay (sec) Unsigned integer
250Ah 1 P0609 Limite frequenza MAX (%) 100-120/OFF P0609 MAX frequency limit (%) Unsigned integer
250Bh 1 P0610 Limite frequenza MIN (%) OFF/80-100 P0610 MIN frequency limit (%) Unsigned integer
250Ch 1 P0611 Ritardo frequenza MIN/MAX (sec) 0-600 P0611 MIN/MAX frequency delay (sec) Unsigned integer
250Dh 1P0612 Controllo RETE OFF/interno/esterno OFF/INT/EXT P0612 MAINS control
OFF/internal/external)Unsigned integer
250Eh 1P0613 Controllo RETE in modoRESET/OFF
OFF/ON/OFF+GLOB/ON+GLOB
P0613 MAINS control in RESET/OFF mode Unsigned integer
250Fh 1P0614 Controllo RETE in modo MAN OFF/ON/OFF+G
LOB/ON+GLOBP0614 MAINS control in MAN mode Unsigned integer
PARAMETRI MENU CONTROLLO GENERATORE ENGINE CONTROL PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2602h 1 P0701 Limite tensione MIN (%) 70-100 P0701 MIN voltage limit (%) Unsigned integer2603h 1 P0702 Ritardo tensione MIN (sec) 0-600 P0702 MIN voltage delay (sec) Unsigned integer
2604h 1 P0703 Limite tensione MAX (%) 100-120 P0703 MAX voltage limit (%) Unsigned integer
2605h 1 P0704 Ritardo tensione MAX (sec) 0-600 P0704 MAX voltage delay (sec) Unsigned integer
2606h 1 P0705 Ritardo generatore nei limiti (sec) 0-600 P0705 Generator into limits delay (sec) Unsigned integer
2607h 1 P0706 Isteresi limiti MIN/MAX(%) 0.0-5.0 P0706 MIN/MAX hysteresis limits (%) Unsigned integer
2608h 1 P0707 Limite asimmetria MAX(%) 5-20 P0707 MAX asymmetry limit (%) Unsigned integer
2609h 1 P0708 Ritardo asimmetria MAX (sec) 0-600 P0708 MAX asymmetry delay (sec) Unsigned integer
260Ah 1 P0709 Limite frequenza MAX (%) 100-120/OFF P0709 MAX frequency limit (%) Unsigned integer
260Bh 1 P0710 Ritardo frequenza MAX (sec) 0-200 P0710 MAX frequency delay (sec) Unsigned integer
260Ch 1 P0711 Limite frequenza MIN (%) OFF/80-100 P0711 MIN frequency limit (%) Unsigned integer
260Dh 1 P0712 Ritardo frequenza MIN (sec) 0-600 P0712 MIN frequency delay (sec) Unsigned integer
260Eh 1 P0713 Controllo gen. OFF/interno/esterno OFF/INT/EXT P0713 Gen. Control (OFF/internal/external) Unsigned integer
260Fh 1 P0714 Ritardo allarmi A27 A28 (sec) 5-240 P0714 A27 A28 alarms delay (sec) Unsigned integer
PARAMETRI MENU PROTEZIONE GENERATORE ENGINE PROTECTION PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2702h 1 P0801 Corrente nominale generatore (A) OFF/5-10000 P0801 Rated generator current (A) Unsigned integer
2703h 1 P0802 Limite corrente max. (%) 100-500/OFF P0802 MAX current limit (%) Unsigned integer
2704h 1 P0803 Ritardo corrente max (sec) 0.0-60.0 P0803 MAX current delay (sec) Unsigned integer
2705h 1 P0804 Scelta curva di protezione (1) P0804 Thermal protection curve selection Unsigned integer
(1) Prima di impostare la classe di protezione, verificare la caratteristica dintervento mediante il software di set-up.Attenzione!! Il TA esterno deve essere scelto in funzione della corrente massima definita nel parametr1 P0802 e P0804.1) Before setting the protection class, it is advisable to check the trip characteristic by means of the set-up software.Caution!! The external CT must be chosen on the basis of the maximum current defined by the parameters P0802 and P0804.
PARAMETRI MENU TEST E MANUTENZIONE TEST E MAINTENANCE PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2802h 1 P0901 Giorno inizio TEST 1-7 P0901 TEST beginning day Unsigned integer
2803h 1 P0902 Ora inizio TEST (h) 00-23 P0902 TEST beginning hour (h) Unsigned integer
2804h 1 P0903 Minuti inizio test (min) 00-59 P0903 TEST beginning Minutes (min) Unsigned integer
2805h 1 P0904 Intervallo tra i TEST (giorni) 1-30 P0904 Interval between TESTS (days) Unsigned integer
2806h 1 P0905 Durata TEST (min) OFF/1-60 P0905 TEST duration (min) Unsigned integer
2807h 1 P0906 Test con carico OFF/ON P0906 Test with load Unsigned integer
2808h 1 P0907 Intervallo di manutenzione (h) OFF/1-999 P0907 Maintenance interval (h) Unsigned integer
2809h 1 P0908 Test automatico con stop esterno OFF/ON P0908 Automatic test with external stop Unsigned integer
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
13/19
Doc: I150IGB01_04.doc 19/12/2003 p. 13 / 19
PARAMETRI MENU PORTA DI COMUNICAZIONE COMUNICATION PORT PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2902h 1 P1001 Indirizzo porta seriale 1-99 P1001 Serial port address Unsigned integer
2903h 1P1002 Baud-Rate RS232 OFF/1200-
38400P1002 RS-232 baud rate Unsigned integer
2904h 1P1003 Baud-Rate RS485 OFF/1200-
38400P1003 RS-485 baud rate Unsigned integer
2905h 1 P1004 Canale modem RS232/RS485 P1004 Modem channel Unsigned integer
2906h 1P1005 Parit 0=no 1=pari
2=dispariP1005 Parity Unsigned integer
2907h 1P1006 Protocollo Rs2332 0=Lovato
1=Modbus RTUP1006 Protocol Rs232 Unsigned integer
2908h 1P1007 Protocollo Rs2485 0=Lovato
1=Modbus RTUP1007 Protocol Rs485 Unsigned integer
PARAMETRI MENU VARIE MISCELLANEOUS PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2A02h 1 P1101 Start su limite max OFF/ON P1101 Max engine power starting Unsigned integer
2A03h 1 P1102 Limite max avviamento (kW) 0-9999 P1102 Engine start threshold (kW) Unsigned integer
2A04h 1 P1103 Ritardo limite max avviamento (sec) 0-999 P1103 Engine start threshold delay (sec) Unsigned integer
2A05h 1 P1104 Limite minimo arresto (kW) 0-9999 P1104 Engine stop threshold (kW) Unsigned integer2A06h 1 P1105 Ritardo limite minimo arresto (sec) 0-999 P1105 Engine stop threshold delay (sec) Unsigned integer
2A07h 1 P1106 Carico fittizio OFF/ON P1106 Dummy load Unsigned integer
2A08h 1 P1107 Carico ON (kW) 0-9999 P1107 Dummy load ON (kW) Unsigned integer
2A09h 1 P1108 Ritardo carico ON (sec) 0-999 P1108 Dummy load ON delay (sec Unsigned integer
2A0Ah 1 P1109 Carico OFF (kW) 0-9999 P1109 Dummy load OFF (kW) Unsigned integer
2A0Bh 1 P1110 Ritardo carico OFF (sec) 0-999 P1110 Dummy load OFF delay (sec) Unsigned integer
2A0Ch 1 P1111 Ore di noleggio (h) 0-60000 P1111 Rent hours (h) Unsigned integer
2A0Dh 1P1112 Scelta modo Normal/EJP/
EJP-T/SCRP1112 Mode select Unsigned integer
2A0Eh 1 P1113 Ritardo start motore (EJP) 0-99 P1113 Start motor delay (EJP) Unsigned integer
2A0Fh 1 P1114 Ritardo commutazione 0-30 P1114 Changeover delay Unsigned integer
2A10h 1 P1115 Blocco ricommutazione OFF/ON P1115 Changeover block Unsigned integer
2A11h 1P1116 Tempo di ciclo on dummy load (min) OFF/1-600 P1116 Dummy load cycle duration ON
(min)Unsigned integer
2A12h 1
P1117 Tempo di ciclo off dummy load (min) OFF/1-600 P1117 Dummy load cycle duration OFF
(min)
Unsigned integer
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
14/19
Doc: I150IGB01_04.doc 19/12/2003 p. 14 / 19
PARAMETRI MENU INPUT PROGRAMMABILI INPUT PROGRAMMABLE PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
(1)Vedi lelenco delle funzioni disponibili nella tabella Ingressi programmabili.(1) See the list of the available functions in the Programmable inputs table.
PARAMETRI MENU USCITE PROGRAMMABILI OUTPUT PROGRAMMABLE PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2C02h 1P1301 Uscita morsetto 5.3-5.4-5.5
(Funzione..)
1 P1301 Output terminal 5.3-5.4-5.5(Function..)
Unsigned integer
2C03h 1P1302 Uscita morsetto 6.2
(Funzione..)
1 P1302 Output terminal 6.2(Function..)
Unsigned integer
2C04h 1P1303 Uscita morsetto 6.3
(Funzione..)
1 P1303 Output terminal 6.3(Function..)
Unsigned integer
2C05h 1P1304 Uscita morsetto 6.5
(Funzione..)
1 P1304 Output terminal 6.5Function..)
Unsigned integer
(1) Vedi lelenco delle funzioni disponibili nella tabella Uscite programmabili(1) See the list of the available functions in the Programmable outputs table.
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2B02h 1 P1201 Ingresso morsetto 8.1 (1) P1201 Input terminal 8.1 Unsigned integer
2B03h 1 8.1 Tipo contatto NO/NC 8.1 Contact type Unsigned integer
2B04h 1 8.1 Ritardo chiusura (sec) 0.0-6000.0 8.1 Opening delay (sec) Unsigned integer
2B05h 1 8.1 Ritardo apertura (sec) 0.0-6000.0 8.1 Closing delay (sec) Unsigned integer
2B06h 1 P1202 Ingresso morsetto 8.2 (1) P1202 Input terminal 8.2 Unsigned integer
2B07h 1 8.2 Tipo contatto NO/NC 8.2 Contact type Unsigned integer2B08h 1 8.2 Ritardo chiusura (sec) 0.0-6000.0 8.2 Opening delay (sec) Unsigned integer
2B09h 1 8.2 Ritardo apertura (sec) 0.0-6000.0 8.2 Closing delay (sec) Unsigned integer
2B0Ah 1 P1203 Ingresso morsetto 8.3 (1) P1203 Input terminal 8.3 Unsigned integer
2B0Bh 1 8.3 Tipo contatto NO/NC 8.3 Contact type Unsigned integer
2B0Ch 1 8.3 Ritardo chiusura (sec) 0.0-6000.0 8.3 Opening delay (sec) Unsigned integer
2B0Dh 1 8.3 Ritardo apertura (sec) 0.0-6000.0 8.3 Closing delay (sec) Unsigned integer
2B0Eh 1 P1204 Ingresso morsetto 8.4 (1) P1204 Input terminal 8.4 Unsigned integer
2B0Fh 1 8.4 Tipo contatto NO/NC 8.4 Contact type Unsigned integer
2B10h 1 8.4 Ritardo chiusura (sec) 0.0-6000.0 8.4 Closing delay (sec) Unsigned integer
2B11h 1 8.4 Ritardo apertura (sec) 0.0-6000.0 8.4 Opening delay (sec) Unsigned integer
2B12h 1 P1205 Ingresso morsetto 8.5 (1) P1205 Input terminal 8.5 Unsigned integer
2B13h 1 8.5 Tipo contatto NO/NC 8.5 Contact type Unsigned integer
2B14h 1 8.5 Ritardo chiusura (sec) 0.0-6000.0 8.5 Closing delay (sec) Unsigned integer
2B15h 1 8.5 Ritardo apertura (sec) 0.0-6000.0 8.5 Opening delay (sec) Unsigned integer
2B16h 1 P1206 Ingresso morsetto 8.6 (1) P1206 Input terminal 8.6 Unsigned integer2B17h 1 8.6 Tipo contatto NO/NC 8.6 Contact type Unsigned integer
2B18h 1 8.6 Ritardo chiusura (sec) 0.0-6000.0 8.6 Closing delay (sec) Unsigned integer
2B19h 1 8.6 Ritardo apertura (sec) 0.0-6000.0 8.6 Opening delay (sec) Unsigned integer
2B1Ah 1 P1207 Ingresso morsetto 8.7 (1) P1207 Input terminal 8.7 Unsigned integer
2B1Bh 1 8.7 Tipo contatto NO/NC 8.7 Contact type Unsigned integer
2B1Ch 1 8.7 Ritardo chiusura (sec) 0.0-6000.0 8.7 Closing delay (sec) Unsigned integer
2B1Dh 1 8.7 Ritardo apertura (sec) 0.0-6000.0 8.7 Opening delay (sec) Unsigned integer
2B1Eh 1 P1208 Ingresso morsetto 8.8 (1) P1208 Input terminal 8.8 Unsigned integer
2B1Fh 1 8.8 Tipo contatto NO/NC 8.8 Contact type Unsigned integer
2B20h 1 8.8 Ritardo chiusura (sec) 0.0-6000.0 8.8 Closing delay (sec) Unsigned integer
2B21h 1 8.8 Ritardo apertura (sec) 0.0-6000.0 8.8 Opening delay (sec) Unsigned integer
2B22h 1 P1209 Ingresso morsetto 8.9 (1) P1209 Input terminal 8.9 Unsigned integer
2B23h 1 8.9 Tipo contatto NO/NC 8.9 Contact type Unsigned integer
2B24h 1 8.9 Ritardo chiusura (sec) 0.0-6000.0 8.9 Closing delay (sec) Unsigned integer
2B25h 1 8.9 Ritardo apertura (sec) 0.0-6000.0 8.9 Opening delay (sec) Unsigned integer
2B26h 1 P1210 Ingresso morsetto 9.1 (1) P1210 Input terminal 9.1 Unsigned integer
2B27h 1 9.1 Tipo contatto NO/NC 9.1 Contact type Unsigned integer
2B28h 1 9.1 Ritardo chiusura (sec) 0.0-6000.0 9.1 Closing delay (sec) Unsigned integer
2B29h 1 9.1 Ritardo apertura (sec) 0.0-6000.0 9.1 Opening delay (sec) Unsigned integer
2B30h 1 P1211 Ingresso morsetto 9.2 (1) P1211 Input terminal 9.2 Unsigned integer
2B31h 1 9.2 Tipo contatto NO/NC 9.2 Contact type Unsigned integer
2B32h 1 9.2 Ritardo chiusura (sec) 0.0-6000.0 9.2 Closing delay (sec) Unsigned integer
2B33h 1 9.2 Ritardo apertura (sec) 0.0-6000.0 9.2 opening delay (sec) Unsigned integer
2B34h 1 P1212 Ingresso morsetto 9.3 (1) P1212 Input terminal 9.3 Unsigned integer
2B35h 1 9.3 Tipo contatto NO/NC 9.3 Contact type Unsigned integer
2B36h 1 9.3 Ritardo chiusura (sec) 0.0-6000.0 9.3 Closing delay (sec) Unsigned integer
2B37h 1 9.3 Ritardo apertura (sec) 0.0-6000.0 9.3 Opening delay (sec) Unsigned integer
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
15/19
Doc: I150IGB01_04.doc 19/12/2003 p. 15 / 19
PARAMETRI MENU INPUT OPTIONAL OPTIONAL INPUT PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
(1)Vedi lelenco delle funzioni disponibili nella tabella Ingressi programmabili.(1) See the list of the available functions in the Programmable inputs table.
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2D02h 1 P1401 Ingresso morsetto I.01 (1) P1401 Input terminal I.01 Unsigned integer
2D03h 1 Tipo contatto NO/NC Contact type Unsigned integer
2D04h 1 Ritardo chiusura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D05h 1 Ritardo apertura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D06h 1 P1402 Ingresso morsetto I.02 (1) P1402 Input terminal I.02 Unsigned integer
2D07h 1 Tipo contatto NO/NC Contact type Unsigned integer2D08h 1 Ritardo chiusura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D09h 1 Ritardo apertura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D0Ah 1 P1403 Ingresso morsetto I.03 (1) P1403 Input terminal I.03 Unsigned integer
2D0Bh 1 Tipo contatto NO/NC Contact type Unsigned integer
2D0Ch 1 Ritardo chiusura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D0Dh 1 Ritardo apertura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D0Eh 1 P1404 Ingresso morsetto I.04 (1) P1404 Input terminal I.04 Unsigned integer
2D0Fh 1 Tipo contatto NO/NC Contact type Unsigned integer
2D10h 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D11h 1 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D12h 1 P1405 Ingresso morsetto I.05 (1) P1405 Input terminal I.05 Unsigned integer
2D13h 1 Tipo contatto NO/NC Contact type Unsigned integer
2D14h 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D15h 1 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D16h 1 P1406 Ingresso morsetto I.06 (1) P1406 Input terminal I.06 Unsigned integer2D17h 1 8.6 Tipo contatto NO/NC Contact type Unsigned integer
2D18h 1 8.6 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D19h 1 8.6 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D1Ah 1 P1407 Ingresso morsetto I.07 (1) P1407 Input terminal I.07 Unsigned integer
2D1Bh 1 Tipo contatto NO/NC Contact type Unsigned integer
2D1Ch 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D1Dh 1 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D1Eh 1 P1408 Ingresso morsetto I.08 (1) P1408 Input terminal I.08 Unsigned integer
2D1Fh 1 Tipo contatto NO/NC Contact type Unsigned integer
2D20h 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D21h 1 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D22h 1 P1409 Ingresso morsetto I.09 (1) P1409 Input terminal I.09 Unsigned integer
2D23h 1 Tipo contatto NO/NC Contact type Unsigned integer
2D24h 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D25h 1 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D26h 1 P1410 Ingresso morsetto I.10 (1) P1410 Input terminal I.10 Unsigned integer
2D27h 1 Tipo contatto NO/NC Contact type Unsigned integer
2D28h 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D29h 1 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D2Ah 1 P1411 Ingresso morsetto I.11 (1) P1411 Input terminal I.11 Unsigned integer
2D2Bh 1 Tipo contatto NO/NC Contact type Unsigned integer
2D2Ch 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D2Dh 1 Ritardo apertura (sec) 0.0-6000.0 opening delay (sec) Unsigned integer
2D2Eh 1 P1412 Ingresso morsetto I.12 (1) P1412 Input terminal I.12 Unsigned integer
2D2Fh 1 Tipo contatto NO/NC Contact type Unsigned integer
2D30h 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D31h 1 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
2D32h 1 P1413 Ingresso morsetto I.13 (1) P1413 Input terminal I.13 Unsigned integer
2D33h 1 Tipo contatto NO/NC Contact type Unsigned integer
2D34h 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D35h 1 Ritardo apertura (sec) 0.0-6000.0 opening delay (sec) Unsigned integer2D36h 1 P1414 Ingresso morsetto I.14 (1) P1414 Input terminal I.14 Unsigned integer
2D37h 1 Tipo contatto NO/NC Contact type Unsigned integer
2D38h 1 Ritardo chiusura (sec) 0.0-6000.0 Closing delay (sec) Unsigned integer
2D39h 1 Ritardo apertura (sec) 0.0-6000.0 Opening delay (sec) Unsigned integer
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
16/19
Doc: I150IGB01_04.doc 19/12/2003 p. 16 / 19
PARAMETRI MENU USCITE OPTIONAL OPTIONAL OUTPUT PARAMETERS MENU(Utilizzabili con funzioni 04 e 06) (To be used with functions 04 and 06)
INDIRIZZOADDRESS
WORDS PARAMETRO RANGE PARAMETER FORMATOFORMAT
2E02h 1P1501 Uscita morsetto O.01
(Funzione..)
1 P1501 Output terminal O.01(Function..)
Unsigned integer
2E03h 1P1502 Uscita morsetto O.02
(Funzione..)
1 P1502 Output terminal O.02(Function..)
Unsigned integer
2E04h 1P1503 Uscita morsetto O.03
(Funzione..)
1 P1503 Output terminal O.03(Function..)
Unsigned integer
2E05h 1P1504 Uscita morsetto O.04
(Funzione..)
1 P1504 Output terminal O.04(Function..)
Unsigned integer
2E06h 1P1505 Uscita morsetto O.05
(Funzione..)
1 P1505 Output terminal O.05(Function..)
Unsigned integer
2E07h 1P1506 Uscita morsetto O.06
(Funzione..)
1 P1506 Output terminal O.06(Function..)
Unsigned integer
2E08h 1P1507 Uscita morsetto O.07
(Funzione..)
1 P1507 Output terminal O.07(Function..)
Unsigned integer
2E09h 1P1508 Uscita morsetto O.08
(Funzione..)
1 P1508 Output terminal O.08(Function..)
Unsigned integer
2E0Ah 1P1509 Uscita morsetto O.09
(Funzione..)
1 P1509 Output terminal O.09(Function..)
Unsigned integer
2E0Bh 1P1510 Uscita morsetto O.10
(Funzione..)
1 P1510 Output terminal O.10(Function..)
Unsigned integer
2E0Ch 1P1511 Uscita morsetto O.11
(Funzione..)
1 P1511 Output terminal O.11(Function..)
Unsigned integer
2E0Dh 1P1512 Uscita morsetto O.12
(Funzione..)
1 P1512 Output terminal O.12(Function..)
Unsigned integer
(1) Vedi lEelenco delle funzioni disponibili nella tabella Uscite programmabili(1) See the list of the available functions in the Programmable outputs table.
Ingressi programmabili (Funzione) Programmable inputs (Function)
0 Disabilitato Disable
1 Pressione olio Oil pressure
2 Temperatura acqua motore Water engine temperature
3 Livello carburante Fuel level
4 Arresto di emergenza Emergency stop
5 Stop a distanza Remote stop
6 Avviamento a distanza Remote starting
7 Avviamento a distanza senza stop Remote starting without cooling
8 Avvia test automatico Start automatic test9 Protezione termica generatore Generator thermal protection
10 Supervisione OFF Supervision Off
11 Blocco setup Set-up block
12 Controllo RETE esterno External MAINS control
13 Controllo GEN esterno External GEN control
14 Telecommutazione Automatic changeover
15 Feed-back contattore RETE MAINS contactor feed-back
16 Feed-back contattore GEN GEN contactor feed-back
17 Serbatoio vuoto Fuel tank empty
18 Start rabbocco Filling start
19 Stop rabbocco Filling stop
20 Serbatoio troppo pieno Fuel tank too full
21 Blocco tastiera (1) Keyboard lock (1)
22 Liquido radiatore Radiator liquid
23 Sirena off Siren off24 Allarme stato interruttore Circuit breaker status alarm
25 Allarme utente 1 Users alarm 1
26 Allarme utente 2 Users alarm 2
27 Allarme utente 3 Users alarm 3
28 Allarme utente 4 Users alarm 4
29 Allarme utente 5 Users alarm 5
30 Allarme utente 6 Users alarm 6
31 Allarme utente 7 Users alarm 7
32 Allarme utente 8 Users alarm 8
(1)Con la funzione Blocco tastiera abilitata i tasti Off/Reset Man Aut Test Start Stop Mains Gen Enter non sono operativi.(1) When the Keyboard lock is enabled, OFF/RESET - MAN AUT TEST- START STOP MAINS GEN ENTER keys are inoperative.
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
17/19
Doc: I150IGB01_04.doc 19/12/2003 p. 17 / 19
Uscite programmabili (Funzione) Programmable outputs (Function)
TABELLA 9: TABLE 9:LISTA EVENTI EVENT LOG(Utilizzabili con funzione 04) (Da rev. firmware 18 alla 21) (To be used with function 04) (From firmware rev. 18 to 21)
INDIRIZZOADDRESS
WORDS PARAMETRO PARAMETER RANGE FORMATOFORMAT
6002h 1 Codice evento nr. 32 (piu recente) Code of event nr. 32 (most recent) 0..62 Unsigned integer
6003h 1 Secondi evento nr. 32 Event nr. 32 - Seconds 0..59 Unsigned integer
6004h 1 Minuti evento nr. 32 Event nr. 32 - Minutes 0..59 Unsigned integer
6005h 1 Ore evento nr. 32 Event nr. 32 - Hours 0..23 Unsigned integer
6006h 1 Giorno evento nr.32 Event nr. 32 - Day 0..31 Unsigned integer
6007h 1 Mese evento nr. 32 Event nr. 32 - Month 1..12 Unsigned integer
6008h 1 Anno evento nr. 32 Event nr. 32 - Year 0..99 Unsigned integer
6009h 1 Codice evento nr. 31 Code of event nr. 31 0..62 Unsigned integer
600Ah 1 Secondi evento nr. 31 Event nr. 31 - Seconds 0..59 Unsigned integer
600Bh 1 Minuti evento nr. 31 Event nr. 31 - Minutes 0..59 Unsigned integer
600Ch 1 Ore evento nr. 31 Event nr. 31 - Hours 0..23 Unsigned integer
600Dh 1 Giorno evento nr. 31 Event nr. 31 - Day 0..31 Unsigned integer
600Eh 1 Mese evento nr. 31 Event nr. 31 - Month 1..12 Unsigned integer
600Fh 1 Anno evento nr. 31 Event nr. 31 - Year 0..99 Unsigned integer
60DBh 1 Codice evento nr. 01 (piu vecchio) Code of event nr. 01 (oldest) 0..62 Unsigned integer
60DCh 1 Secondi evento nr. 01 Event nr. 01 - Seconds 0..59 Unsigned integer
60DDh 1 Minuti evento nr. 01 Event nr. 01 - Minutes 0..59 Unsigned integer
60DEh 1 Ore evento nr. 01 Event nr. 01 - Hours 0..23 Unsigned integer
60DFh 1 Giorno evento nr. 01 Event nr. 01 - Day 0..31 Unsigned integer
60E0h 1 Mese evento nr. 01 Event nr. 01- Month 1..12 Unsigned integer
60E1h 1 Anno evento nr. 01 Event nr. 01 - Year 0..99 Unsigned integer
Il significato del codice dellevento puo essere determinato nella seguente tabella. In caso non siano registrati eventi viene ritornato il codice 0.The meaning of the event code can be found in the following table. In case there is no recorded event code 0 will be returned
0 Disabilitata Disable
1 Allarme globale Global alarm
2 Elettrovalvola carburante Fuel solenoid valve
3 Sirena Siren
4 Deceleratore Decelerator
5 Magnete stop Stop magnet
6 Candelette Glow-plugs
7 Valvola gas Gas valve
8 Valvola aria Air valve
9 Valvola cicchetto Priming valve\0 Pompa rabbocco Topping-up pump
11 Carico fittizio Dummy load
12 Aria compressa Compressed air
13 Modo funzionamento Operating mode
14 Rete non presente Mains not present
15 Motore in moto Engine running
16 Motore in allarme Engine failure
17 Basso carburante Low fuel level
18 Carico fittizio L1 Dummy load L1
19 Carico fittizio L2 Dummy load L2
20 Carico fittizio L3 Dummy load L3
21 Allarme globale 1 Global alarm 2
22 Allarme globale 2 Global alarm 3
23-76 Allarmi A1-A45 e UA1-UA8 A1-A45 and UA1-UA8 alarms
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
18/19
Doc: I150IGB01_04.doc 19/12/2003 p. 18 / 19
TABELLA 9: TABLE 9:LISTA EVENTI EVENT LOG(Utilizzabili con funzione 04) (Da rev. firmware 22) (To be used with function 04) (From firmware rev. 22)
INDIRIZZOADDRESS
WORDS PARAMETRO PARAMETER RANGE FORMATOFORMAT
6002h 1 Codice evento nr. 255 (piu recente) Code of event nr. 255 (most recent) 0..62 Unsigned integer
6003h 1 Secondi evento nr. 255 Event nr. 255 - Seconds 0..59 Unsigned integer
6004h 1 Minuti evento nr. 255 Event nr. 255 - Minutes 0..59 Unsigned integer
6005h 1 Ore evento nr. 255 Event nr. 255 - Hours 0..23 Unsigned integer
6006h 1 Giorno evento nr.255 Event nr. 255 - Day 0..31 Unsigned integer6007h 1 Mese evento nr. 255 Event nr. 255 - Month 1..12 Unsigned integer
6008h 1 Anno evento nr. 255 Event nr. 255 - Year 0..99 Unsigned integer
6009h 1 Codice evento nr. 254 Code of event nr. 254 0..62 Unsigned integer
600Ah 1 Secondi evento nr. 254 Event nr. 254 - Seconds 0..59 Unsigned integer
600Bh 1 Minuti evento nr. 254 Event nr. 254 - Minutes 0..59 Unsigned integer
600Ch 1 Ore evento nr. 254 Event nr. 254 - Hours 0..23 Unsigned integer
600Dh 1 Giorno evento nr. 254 Event nr. 254 - Day 0..31 Unsigned integer
600Eh 1 Mese evento nr. 254 Event nr. 254 - Month 1..12 Unsigned integer
600Fh 1 Anno evento nr. 254 Event nr. 254 - Year 0..99 Unsigned integer
66F4h 1 Codice evento nr. 01 (piu vecchio) Code of event nr. 01 (oldest) 0..62 Unsigned integer
66F5h 1 Secondi evento nr. 01 Event nr. 01 - Seconds 0..59 Unsigned integer
66F6h 1 Minuti evento nr. 01 Event nr. 01 - Minutes 0..59 Unsigned integer
66F7h 1 Ore evento nr. 01 Event nr. 01 - Hours 0..23 Unsigned integer
66F8h 1 Giorno evento nr. 01 Event nr. 01 - Day 0..31 Unsigned integer
66F9h 1 Mese evento nr. 01 Event nr. 01- Month 1..12 Unsigned integer
66FAh 1 Anno evento nr. 01 Event nr. 01 - Year 0..99 Unsigned integer
Il significato del codice dellevento puo essere determinato nella seguente tabella. In caso non siano registrati eventi viene ritornato il codice 0.The meaning of the event code can be found in the following table. In case there is no recorded event code 0 will be returned.
Num Cod. Messaggio0 E01 Modalit selezionata RESET
1 E02 Modalit selezionata MAN
2 E03 Modalit selezionata AUT3 E04 Modalit selezionata TEST
4 E05 Motore in moto (alt. c.b.)
5 E06 Motore in moto (frequenza generatore)
6 E07 Motore in moto (tensione generatore)
7 E08 Motore in moto (segnale 'W')
8 E09 Arresto motore
9 E10 Tentativo di avviamento
10 E11 Comando di START manuale
11 E12 Comando di STOP manuale
12 E13 Comando manuale contattore di rete
13 E14 Comando manuale contattore generatore
14 E15 Tensione rete nei limiti
15 E16 Tensione rete fuori dai limiti
16 E17 Contattore rete chiuso
17 E18 Contattore rete aperto18 E19 Tensione generatore nei limiti
19 E20 Tensione generatore fuori dai limiti
20 E21 Contattore generatore chiuso
21 E22 Contattore generatore aperto
22 E23 Inizio del controllo remoto
23 E24 Fine del controllo remoto
24 E25 Accesso al menu Utility dalla tastiera frontale
25 E26 Accesso al menu Generale dalla tastiera frontale
26 E27 Accesso al menu Batteria dalla tastiera frontale
27 E28 Accesso al menu Avviamento motore dalla tastiera frontale
28 E29 Accesso al menu Controllo motore dalla tastiera frontale
29 E30 Accesso al menu Controllo rete dalla tastiera frontale
30 E31 Accesso al menu Controllo generatore dalla tastiera frontale
31 E32 Accesso al menu Protezione generatore dalla tastiera frontale
32 E33 Accesso al menu Test e manutenzione dalla tastiera frontale
33 E34 Accesso al menu Porta di comunicazione dalla tastiera frontale
34 E35 Accesso al menu Varie dalla tastiera frontale
35 E36 Accesso al menu Input programmabili dalla tastiera frontale
Cod. MessageE01 RESET mode select
E02 MAN mode select
E03 AUT mode selectE04 TEST mode select
E05 Motor running (alt. c.b.)
E06 Motor running (generator frequency)
E07 Motor running (generator voltage)
E08 Motor running (signal 'W')
E09 Motor stop
E10 Starting attempt number
E11 START manual command
E12 STOP manual command
E13 Mains contactor manual command
E14 Generator contactor manual command
E15 Mains voltage into limits
E16 Main voltage out of limits
E17 Mains contactor close
E18 Mains contactor openE19 Generator voltage into limits
E20 Generator voltage out of limits
E21 Generator contactor close
E22 Generator contactor open
E23 Start remote control
E24 End remote control
E25 Access to utility menu from front keyboard
E26 Access to general menu from front keyboard
E27 Access to battery menu from front keyboard
E28 Access to starting motor menu from front keyboard
E29 Access to engine control menu from front keyboard
E30 Access to mains control menu from front keyboard
E31 Access to engine control menu from front keyboard
E32 Access to engine protection menu from front keyboard
E33 Access to test & maintenance menu from front keyboard
E34 Access to communication port menu from front keyboard
E35 Access to miscellaneous menu from front keyboard
E36 Access to programmable input menu from front keyboard
8/13/2019 Rgk60 Modul Lovato 3 Modbus Protokol
19/19
Cod. MessageE37 Access to programmable output menu from front keyboard
E38 Access to optional programm. out menu from front keyboard
E39 Access to optional programm. Input menu from front keyboard
E40 Access to alarms table 1 menu from front keyboard
E41 Access to alarms table 2 menu from front keyboard
E42
E43 Access to utility menu from remote control
E44 Access to general menu from remote control
E45 Access to battery menu from remote control
E46 Access to starting motor menu from remote controlE47 Access to engine control menu from remote control
E48 Access to mains control menu from remote control
E49 Access to engine control menu from remote control
E50 Access to engine protection menu from remote control
E51 Access to test & maintenance menu from remote control
E52 Access to communication port menu from remote control
E53 Access to miscellaneous menu from remote control
E54 Access to programmable input menu from remote control
E55 Access to programmable output menu from remote control
E56 Access to optional programm. out menu from remote control
E57 Access to optional programm. Input menu from remote control
E58 Access to alarms table 1 menu from remote control
E59 Access to alarms table 2 menu from remote control
E60
E61 Software resetE62 Power down
E63 Parameters to default
Num Cod. Messaggio36 E37 Accesso al menu Output programmabili dalla tastiera frontale
37 E38 Accesso al menu Input optional dalla tastiera frontale
38 E39 Accesso al menu Output optional dalla tastiera frontale
39 E40 Accesso al menu Tabella Allarmi 1 dalla tastiera frontale
40 E41 Accesso al menu Tabella Allarmi 2 dalla tastiera frontale
41 E42
42 E43 Accesso al menu Utility da controllo remoto
43 E44 Accesso al menu Generale da controllo remoto
44 E45 Accesso al menu Batteria da controllo remoto
45 E46 Accesso al menu Avviamento motore da controllo remoto46 E47 Accesso al menu Controllo motore da controllo remoto
47 E48 Accesso al menu Controllo rete da controllo remoto
48 E49 Accesso al menu Controllo generatore da controllo remoto
49 E50 Accesso al menu Protezione generatore da controllo remoto
50 E51 Accesso al menu Test e manutenzione da controllo remoto
51 E52 Accesso al menu Porta di comunicazione da controllo remoto
52 E53 Accesso al menu Varie da controllo remoto
53 E54 Accesso al menu Input programmabili da controllo remoto
54 E55 Accesso al menu Output programmabili da controllo remoto
55 E56 Accesso al menu Input optional da controllo remoto
56 E57 Accesso al menu Output optional da controllo remoto
57 E58 Accesso al menu Tabella Allarmi 1 da controllo remoto
58 E59 Accesso al menu Tabella Allarmi 2 da controllo remoto
59 E60
60 E61 Reset software61 E62 Mancanza alimentazione
62 E63 Parametri a default